hmm...
I had a similar error once....
try re-running syslinux on your new boot.img (the one with your kernel on it)
http://syslinux.zytor.com/
I have seen several reports of this problem in the forum, but no solutions.
I tried to modify the kernel in a CD-boot Knoppix (I needed devfs support, so I grabbed the Knoppix-kernel-source package, kept the same kernel config except for devfs, and recompiled). When I boot the CD, it grabe root.img, and then gives the following message:
Kernel panic : No init found. Try passing init= option to kernel
If I use the default boot.img, my slightly modified Knoppix CD boots fine. It's only when I try to use the image with my kernel that I have problems.
When I made the new boot.img, I modified as little as possible. I kept the same mroot, I just replaced the kernel.
Is there something else I'm missing? Or, does anyone else have a working boot.img that includes a kernel with devfs support?
Thanks,
Todd
hmm...
I had a similar error once....
try re-running syslinux on your new boot.img (the one with your kernel on it)
http://syslinux.zytor.com/
That is the last message but what about other messages like can the script linuxrc find your clooped image and mount it etc.
INIT not found just mean that when the linuxrc exit, the kernel will proceed to use the new root system and search for /etc/init to run and failed. So the most likely cause(as KNOPPIX doesn't not switch real root device) would be that it failed to mount the image does the KNOPPIX fs is not 'imported' in.
More messages are needed.
I would imagine that you don't have the necessary kernel modules in your initial root filesystem (I suppose that's boot.img) to mount your root filesystem. At least, that's my experience from other distributions and from the typical behaviour of "make install" on the Linux kernel sources.Originally Posted by tji
My standard workaround when trying out a custom kernel is to reuse the old initial root filesystem image for the shipped kernel and to replace the kernel and modules in that image (or rather a copy of it). I don't know how wise that is, but the standard kernel Makefiles don't really help me find a reliable alternative.Originally Posted by tji
I've run into this problen myself. To be safe you should replace the kernel modules in the miniroot and recompile cloop and replace that, but this is not the cause of your problem. I beleve that your problem is caused by the init in the miniroot being uncompatable with your new kernel. In the case of knoppix init is statically linked with ash (the initial shell). So you will need to recompile ash-knoppix against your new kernel and sources(it's on Klaus's site somewhere).
jTal
Juniper EX2300-C-12P, 12 Port FANLESS POE Ethernet Switch EX2300-C
$375.00
Juniper Networks EX2300-C-12T Compact 12-Port EX2300-C Series Ethernet Switch
$300.00
Juniper Networks EX2200-C Gigabit Ethernet Managed Switch | EX2200-C-12P-2G
$49.99
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$59.95
Juniper EX3400-48P 48 Port Switch PoE+ 4x SFP+ 2x QSFP 1xAC *Tested/Warranty*
$139.95
Juniper Networks EX3300-24P | 24 Port Gigabit Network Switch w/ Power cord
$53.99
Juniper Networks EX4300-48P-TAA 48-Port Switch with PoE+
$99.00
Juniper QFX5100-48T 48-Port 10G SFP 6-Port 40G QSFP Ethernet Switch Tested
$312.69
Juniper Networks EX4400-48MP 48 port 5GbE + 12 port 10 Gigabit PoE++ Switch -NEW
$1200.00
Juniper Networks EX2300-48P 48 Port Gigabit PoE 4 SFP 1/10G Network Switch
$185.00