-
How do I enable touchpad-tapping?
Hello everyone. I am new in this forum. Knoppix is a great Linux distro. I write a software for an old computer, without mouse and keyboard - only with touchscreen (i think - it use the same drivers like touchpad, so I'm testing my application on laptop). But touchpad-tapping (i want to it mean click) i disabled. I have downloaded synaptics drivers from repositories, but it still not works. What I must do to enable it? Change something in /etc/X11/xorg.conf ? Thank you in advance, rr
-
Senior Member
registered user
[there is a emoticon on top which I can't remove]
There are two ways to go about this, as you have noted, one is to modify /etc/X11/xorg.conf. Because knoppix xorg.conf is script generated, you will have understand the needed syntax and as well as understand which script is the one generating it.
Alternatively, this is what I would do it. Firstly make sure you have this program 'synclient', check that it exists :-
( this will list all the available settings ).
If it does not exist, you would have to install xserver-xorg-input-synaptic.
After that go to /etc/X11/Xsession.d and add a file say '15x11-synaptics' with this content :-
Code:
#
synclient "TapButton1=1"
That's all which is needed. After you restarted Xserver, tap-to-click will be working.
Last edited by kl522; 09-27-2010 at 10:59 PM.
-
Senior Member
registered user
@kl522
Thank you for providing this valuable information.
I use the command
Code:
synclient TapButton1=1 TapButton2=3 TapButton3=2
to enable tapping with two and three fingers. Tapping with two fingers is set to button 3 because clicking with the right button is more often than clicking with the middle button.
-
thanks, it works
-
Senior Member
registered user
You are fully justified to use tap-to-click on a system without keyboard and mouse.
I use touchpad on a typical notebook, personally I consider tap-to-click a nuisance.
However I do this :-
synclient "HorizEdgeScroll=1"
to allow me to use horizontal scroll on the edge of the touchpad.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Juniper MX104-AC 4 MIC Slot Chassis w/ 2x RE-S-MX104 and 2x PWR-MX104-AC
$1899.00
*New* MIC-MRATE Juniper 12-Port Multi-Rate MIC module
$749.00
Juniper 48-Port GbE PoE+ & 4-Port 10GB SFP+ Managed Network Switch EX3300-48P
$49.99
Juniper Networks EX2300-24P 24 Port Gigabit PoE 4 SFP 1/10G Network Switch
$119.00
Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord
$54.99
Juniper EX4300-48T 48 Port 1G 4 QSFP 40G Dual PSU AFO w/ Rails, EX-UM-4X4SFP Mod
$169.00
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch
$50.95
Juniper EX3400-48P 48-Port PoE+ 4x SFP+ 2x 40G QSFP+ Dual PSU & Fan AFO Switch
$269.99
Juniper QFX5100-48S 48-Port 10GbE SFP+ 6x40GbE QSFP Network Switch w/Ears Tested
$599.99
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$315.00