-
v6.2.1 CD boot error: Input/output error
Successfully:
Verified CD with boot option 'knoppix testcd'
Past mounting /mnt-system
Past mounting /KNOPPIX
Past mounting /UNIONFS
Past symlinks to /UNIONFS
Following error found:
/init: exec: line 742: /sbin/init: input/output error
The following cheat codes were used with no success.
knoppix vga=0
knoppix (1-5)
knoppix acpi=off noapic nolapic pci=bios hpet=off nodma
knoppix acpi=off pnpbios=off noapic noapm
knoppix vga=0 debug -b 3
Using 'debug' boot option and typing 'exit' at each prompt, the system stalls at the following prompt:
BusyBox v1.14.2 (Debian 1:1.14.2-2) built-in shell (ash)
Enter 'help' for a list of built-in commands.
sh: can't access tty; job control turned off
/ #
At this point, I typed 'exit' and then 'init 5' but still have a blank screen.
-
Senior Member
registered user
The input/output error thingie with /sbin/init, seems to be a fairly common problem, not limited to knoppix only. The errors seem to be due to /sbin/init failed to open /dev/console for input/output, but nobody seems to have found out why it happens only to certain systems :-
http://www.linuxquestions.org/questi...-error-397113/
Perhaps you can try to debug it by checking the permission of /dev/console and also do some chmod, when you run it under debug mode.
Cheers.
-
Solution found
Thanks 'kl522' for your suggestion, however, it seems that 'input/output' error could be due to many possible causes. To change the permissions on a clean downloaded distribution doesn't make sense.
In my case the problem was with my CD which explains why a file could not be read i.e. input error.
My solution was simple:
- used a new, clean, high-quality 700MB CDR
- burned at slowest speed 4x
- OPTIONAL: increased the cache and RAM buffer size
As per the forums, most errors are due to:
1. Incomplete/bad download
2. Bad burn
-
Administrator
Site Admin-
Originally Posted by
peter.hentrich
As per the forums, most errors are due to:
1. Incomplete/bad download
2. Bad burn
yup, and both easily preventable:
1) Use the torrents rather than the mirrors, and do the simple md5 test. If you don't want to learn how to do either because you have never done them before, then it is very likely that Knoppix and Linux are not for you and you should stay with Windows.
2) Burning at slow speed, as an ISO, with burning software that supports both ISO burning and verification after burning (such as Nero) with verification enabled should give a good burn.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
Downloads and burning
Harry, thanks for your experienced advice and patience with first-timers like me.
These are simple measures to ensure successful CD/DVDs:
1a) Use the torrents rather than the mirrors
Yes, this is the best option. Using a torrent does not eliminate errors though, as I discovered. Whether by user error or otherwise, my 'uTorrent' download was incomplete even when it said "finished". I had to re-check/re-start my download.
1b) Do the simple md5 test
Yes, this step should be mandatory after a finished download. Foolishly, I ignored this hash key verification and trusted my torrent application to verify the complete download.
For an explanation of the procedure, go to:
http://www.knoppix.net/wiki/Downloading_FAQ#Q:_What_are_these_strange_MD5_file s_that_accompany_the_ISO_CD_images.3F
It's a single command:
Code:
md5sum -c KNOPPIX_xxxxxxxx.iso.md5
Here is the erraneous output after my first attempt of the uTorrent download:
Code:
md5sum -c KNOPPIX_V6.2.1CD-2010-01-31-EN.iso
md5sum: @@@@@@@@@@@@@@@@@@@@@@@@@@ : No such file or directory
@@@@@@@@@@@@@@@@@@@@@@@@@@ : FAILED open or read
md5sum: int1e = %08x: No such file or directory
int1e = %08x: FAILED open or read
md5sum: WARNING: 2 of 2 listed files could not be read
Here is the successful output after I 're-checked' and 're-started' my uTorrent download:
Code:
md5sum -c KNOPPIX_V6.2.1CD-2010-01-31-EN.iso.md5
KNOPPIX_V6.2.1CD-2010-01-31-EN.iso: OK
Knoppix is working and an important lesson learned.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell Optiplex 5060 SFF 8th Gen Core i7 3.2GHZ 16GB 512GB Win 11 Pro
$249.00
Lenovo Loq 15Irh8 15" Laptop Core i5-13420H GeForce RTX 2050 16GB 512GB SSD W11H
$499.99
Intel - Core i9-13900K 13th Gen 24 cores 8 P-cores + 16 E-cores 36M Cache, 3 ...
$689.99
AMD Ryzen 9 5950X 16-core 32-thread Desktop Processor
$319.99
Intel - Core i7-13700K 13th Gen 16 cores 8 P-cores + 8 E-cores 30M Cache, 3.4...
$489.99
Dell OptiPlex 7060 Micro 8-Core i7 8700 3.20GHz 16GB 512GB SSD Win 11 Pro
$214.00
AMD Ryzen 7 7800X3D 8-Core - 16-Thread 4.2 GHz (5.0 GHz Max Boost) Socket A...
$339.95
Apple Mac Pro Processor Tray 5,1 2010 2012 2.4ghz 8 core
$79.99
Lenovo IdeaCentre 3 07IRB8 Desktop Intel Core i5-13400 16GB 512GB SSD W11H
$429.99
HP Workstation Z640 2x Xeon E5-2623V4 32GB Ram Dual 256GB SSD K420 Linux GA
$234.98