-
v6.2.1 CD boot error: Input/output error
Successfully:
Verified CD with boot option 'knoppix testcd'
Past mounting /mnt-system
Past mounting /KNOPPIX
Past mounting /UNIONFS
Past symlinks to /UNIONFS
Following error found:
/init: exec: line 742: /sbin/init: input/output error
The following cheat codes were used with no success.
knoppix vga=0
knoppix (1-5)
knoppix acpi=off noapic nolapic pci=bios hpet=off nodma
knoppix acpi=off pnpbios=off noapic noapm
knoppix vga=0 debug -b 3
Using 'debug' boot option and typing 'exit' at each prompt, the system stalls at the following prompt:
BusyBox v1.14.2 (Debian 1:1.14.2-2) built-in shell (ash)
Enter 'help' for a list of built-in commands.
sh: can't access tty; job control turned off
/ #
At this point, I typed 'exit' and then 'init 5' but still have a blank screen.
-
Senior Member
registered user
The input/output error thingie with /sbin/init, seems to be a fairly common problem, not limited to knoppix only. The errors seem to be due to /sbin/init failed to open /dev/console for input/output, but nobody seems to have found out why it happens only to certain systems :-
http://www.linuxquestions.org/questi...-error-397113/
Perhaps you can try to debug it by checking the permission of /dev/console and also do some chmod, when you run it under debug mode.
Cheers.
-
Solution found
Thanks 'kl522' for your suggestion, however, it seems that 'input/output' error could be due to many possible causes. To change the permissions on a clean downloaded distribution doesn't make sense.
In my case the problem was with my CD which explains why a file could not be read i.e. input error.
My solution was simple:
- used a new, clean, high-quality 700MB CDR
- burned at slowest speed 4x
- OPTIONAL: increased the cache and RAM buffer size
As per the forums, most errors are due to:
1. Incomplete/bad download
2. Bad burn
-
Administrator
Site Admin-
Originally Posted by
peter.hentrich
As per the forums, most errors are due to:
1. Incomplete/bad download
2. Bad burn
yup, and both easily preventable:
1) Use the torrents rather than the mirrors, and do the simple md5 test. If you don't want to learn how to do either because you have never done them before, then it is very likely that Knoppix and Linux are not for you and you should stay with Windows.
2) Burning at slow speed, as an ISO, with burning software that supports both ISO burning and verification after burning (such as Nero) with verification enabled should give a good burn.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
Downloads and burning
Harry, thanks for your experienced advice and patience with first-timers like me.
These are simple measures to ensure successful CD/DVDs:
1a) Use the torrents rather than the mirrors
Yes, this is the best option. Using a torrent does not eliminate errors though, as I discovered. Whether by user error or otherwise, my 'uTorrent' download was incomplete even when it said "finished". I had to re-check/re-start my download.
1b) Do the simple md5 test
Yes, this step should be mandatory after a finished download. Foolishly, I ignored this hash key verification and trusted my torrent application to verify the complete download.
For an explanation of the procedure, go to:
http://www.knoppix.net/wiki/Downloading_FAQ#Q:_What_are_these_strange_MD5_file s_that_accompany_the_ISO_CD_images.3F
It's a single command:
Code:
md5sum -c KNOPPIX_xxxxxxxx.iso.md5
Here is the erraneous output after my first attempt of the uTorrent download:
Code:
md5sum -c KNOPPIX_V6.2.1CD-2010-01-31-EN.iso
md5sum: @@@@@@@@@@@@@@@@@@@@@@@@@@ : No such file or directory
@@@@@@@@@@@@@@@@@@@@@@@@@@ : FAILED open or read
md5sum: int1e = %08x: No such file or directory
int1e = %08x: FAILED open or read
md5sum: WARNING: 2 of 2 listed files could not be read
Here is the successful output after I 're-checked' and 're-started' my uTorrent download:
Code:
md5sum -c KNOPPIX_V6.2.1CD-2010-01-31-EN.iso.md5
KNOPPIX_V6.2.1CD-2010-01-31-EN.iso: OK
Knoppix is working and an important lesson learned.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
SQL Server 2019 Standard (10 CAL) - Windows and Linux, Physical License NEW
$178.45
Microsoft SQL Server 2019 Standard (10 CAL) Windows, Linux Physical License, NEW
$178.99
1U BareMetal pfsense opnsense Router Firewall DNS Server 6x 10GB Ethernet Ports
$169.00
IBM X3200 M3 Tower Server Intel Xeon X3450 2.67GHz 2GB 2*500 Gb Hdd Linux AS IS
$60.00
NEW Redhat Enterprise Linux 7 Server Edition (Factory Sealed)
$25.00
Custom Laptop, Desktop or Server Badge - Set of 12 (Select your Linux distro)
$5.45
IBM E850 Power8 2x 12C 3.02GHz 512Gb 1.8Tb SAS 10GbE 16Gb Linux Server 8408-E8E
$699.95
1U Server 15" Depth X11SSH-F E3-1270 V6 3.8Ghz 4 Core 32GB RAM 240G SSD
$250.00
Linux Multi-Boot USB Installer 13-in-1 | Dual USB-A & USB-C | Ubuntu, Mint, Etc
$19.99
Supermicro 2U 12-bay X8DT6 2x Xeon E5640, 250GB Boot HDD, 128GB RAM, Dual PS
$295.00