Glen Millard:
Knoppix 6.2 and Windows XP quagmire
......and I don't mean the pervert from 'Family Guy' either!
Okay, so I have an XP Pro install and I am getting the BSOD (big surprise).
I want to see if I can at *least* recover my data on the disk and then I
am going to wipe it and put something else on there (Ubuntu, Debian,
Fedora) which I have been meaning to do for quite some time.
So, I have Knoppix 6.2 and I was able to boot with it. Now I am having
trouble identifying the hard drive. In the 'dmesg' output, I can see :
ata1: SATA link up 1.5 Gbps but I cannot see the drive in the device list.
So, how would I identify the drive and mount it so I can at least get
all of my important stuff off of there before I send XP back to that
Great Gig In The Sky?
Thanks
Klaus Knopper:
Hello Mr. Millard,
On Fri, May 27, 2011 at 02:13:23PM -0400, Glen Millard wrote:
> ...and I don't mean the pervert from 'Family Guy' either!
>
> Okay, so I have an XP Pro install and I am getting the BSOD (big
> surprise).
> I want to see if I can at *least* recover my data on the disk and then I
> am going to wipe it and put something else on there (Ubuntu, Debian,
> Fedora) which I have been meaning to do for quite some time.
>
> So, I have Knoppix 6.2 and I was able to boot with it. Now I am having
> trouble identifying the hard drive. In the 'dmesg' output, I can see :
> ata1: SATA link up 1.5 Gbps but I cannot see the drive in the device list.
Usually, it should at least appear in
cat /proc/parttions
as sda, sda1, sda2, ...
If not, the harddisk controller may be unsupprted. Knoppix 6.2 is
probably older than your computer, I would recommend trying 6.4.4 or
6.5 which have never kernels and hardware support.
> So, how would I identify the drive and mount it so I can at least get
> all of my important stuff off of there before I send XP back to that
> Great Gig In The Sky?
The filemanager should show your harddisk as "sda1" on the left side. If it doesn't, the partition table of the drive may just be broken, please check if you at least see "sda" (the entire disk) in /proc/partitions.
If you see the disk, you can repartition with "sudo fdisk /dev/sda", or
try to recover the old partition table by "sudo testdisk".
Hope this helps.
Regards
-Klaus Knopper
Cisco Catalyst C9300-24UX-A 24 Port 10G/mGig Copper UPOE Network Switch
$499.00
Cisco Catalyst C9300-24UX-A 24 Port 10G/mGig UPOE Network Switch, no module
$279.97
Cisco WS-C2960X-48FPD-L 48 V07 POE+ GE+2 10G SFP+, LAN BASE 740W w/ C2960X-Stack
$140.00
Cisco Nexus N9K-C93108TC-EX 48-Port 10G RJ-45 6x100G QSFP Network Switch W/Ears
$499.99
Cisco C3850-NM-2-10G 2 Port Network Exp.Module for 3850
$30.99
Cisco SFP-10G-SR 10-2415-03 10 Gigabit Transceiver LOT OF 10 @ C
$39.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Cisco C3850-NM-4-10G 4 Port Network Exp.Module for 3850
$124.90
Cisco AIR-CT3504-K9 Wireless Controller No AC Adapter 15-4
$299.99
Cisco Nexus N9K-C9372TX 48P 10G Gigabit Ethernet 6x QSFP+ 40G Switch 2x650W PSU
$199.99