Results 1 to 3 of 3

Thread: Net via Bluetooth

  1. #1
    Junior Member
    Join Date
    Nov 2011
    Posts
    1

    Net via Bluetooth

    Hi. I am new to Knoppix. I have a laptop with a crashed IDE hard drive. I am thinking of using Knoppix on a flash drive to run it.
    When I had windows on it I used a pair of bluetooth dongles to pair the laptop with my PC and shared the PC's internet (wired) connection. and used the PC's internet connection to go on the net with the laptop. I don't have a wireless router. And the laptop did not come with Bluetooth.
    Can this be done with Knoppix. Could knopppix use bluetooth to access a windows PC's internet connection.
    Thank you.

  2. #2
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    @ Capt_T

    Welcome to the forum.

    You can access the internet either by ethernet or wifi wireless
    independent of a Windows setup with either Knoppix LiveUSB or LiveCD.
    Using Bluetooth to tap into a Windows setup is unnecessary.

    I usually make a LiveCD and from that a LiveUSB. Look for Knoppix 6.7.1;
    but, be aware that the ADRIANE versions are for 'vision-challenged' users.

    Also, I think it may be possible to make a Knoppix LiveUSB in Windows using a
    Pendrive program without first making a LiveCD.

    Keep us informed of your progress.

  3. #3
    Senior Member registered user
    Join Date
    Feb 2010
    Posts
    512
    @ Capt_T

    Knoppix can be used to create a PAN using bluetooth adapters. I succeeded in connecting a Knoppix V6.7.1 notebook to a Windows 7 Pro system. I used Knoppix 6.7.1 CD and had to add a package bluez-compat containing the program pand. I had to create a configuration file /etc/dbus-1/system.d/bluetooth.conf that is missing in Knoppix V6.7.1 because the bluetooth was not allowed to connect to the D-Bus. I copied the configuration file from Knoppix 6.4.4 and added one line. The current file has the following content
    Code:
    <!-- This configuration file specifies the required security policies
         for Bluetooth core daemon to work. -->
    
    <!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-BUS Bus Configuration 1.0//EN"
     "http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
    <busconfig>
    
      <!-- ../system.conf have denied everything, so we just punch some holes -->
    
      <policy user="root">
        <allow own="org.bluez"/>
        <allow send_destination="org.bluez"/>
    
        <!-- allow root to send to agents -->
        <allow send_interface="org.bluez.Agent"/>
        <allow send_interface="org.bluez.Proximity"/>
    
      </policy>
    
      <!-- allow users at the console, see consolekit or libpam-foreground -->
      <policy at_console="true">
        <allow send_destination="org.bluez"/>
      </policy>
    
      <!-- allow users of bluetooth group to communicate with hcid -->
      <policy group="bluetooth">
        <allow send_destination="org.bluez"/>
      </policy>
    
      <policy context="default">
        <deny send_destination="org.bluez"/>
      </policy>
    
    </busconfig>
    I downloaded and installed the package bluez-compat and created the the configuration file. Then I configured my Windows 7 Pro system so that it accepted bluetooth connections and served as DHCP server. Afterwards I plugged in my second USB bluetooth adapter at my Knoppix system. Afer having waited a few seconds I issued
    Code:
    hciconfig
    lsmod |grep bnep
    hcitool scan
    The first command told that the bluetooth was up and running. The second one said that the kernel module bnep was installed. The last command showed bluetooth systems waiting for connections. I issued
    Code:
    bluetooth-wizard
    and was able to connect to the bluetooth adapter of my Windows 7 system. From the hcitool command I knew the MAC address of the Windows 7 system (00:1F:23:34:45:67). I issued
    Code:
    sudo pand --role PANU --service GN --nodetach -c 00:1F:23:34:45:67
    and created a PAN. The last step was to fetch the network configuration from the DHCP server. Therefore I issued
    Code:
    sudo dhclient bnep0
    ifconfig bnep0
    and saw that the new network adapter was properly configured. I also learned the IP address of my Knoppix system.

    On the Knoppix system I started the ssh server and connected to it from the Windows 7 system using the program WinSCP with the IP address I learned before. I did not experienced any problems in doing so.

    The Windows 7 system is connected to the WLAN. I was not able to establish a connection between the PAN and the WLAN. Thus I cannot reach the Internet from my notebook via bluetooth although I entered the nameserver of the WLAN in the file /etc/resolv.conf.

    Does anybody know how to connect the two networks on the Windows 7 Pro system?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24 picture

Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24

$117.00



GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE picture

GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE

$74.99



H3C SFP-FE-T-A Compatible 100BASE-T SFP Copper RJ-45 100m -93651 picture

H3C SFP-FE-T-A Compatible 100BASE-T SFP Copper RJ-45 100m -93651

$38.00



Sonicwall 02-SSC-1874 Compatible 10GBASE-T Copper SFP+ RJ-45 30M Transceiver-876 picture

Sonicwall 02-SSC-1874 Compatible 10GBASE-T Copper SFP+ RJ-45 30M Transceiver-876

$189.05



Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03  picture

Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03

$8.00



For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Module 10G SFP+ to RJ45 10GBase-T picture

For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Module 10G SFP+ to RJ45 10GBase-T

$48.59



OEM Cisco GLC-T 30-1410-04 1000BASE-T SFP Ethernet Transceiver Module, tested picture

OEM Cisco GLC-T 30-1410-04 1000BASE-T SFP Ethernet Transceiver Module, tested

$9.40



NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping* picture

NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping*

$15.00



LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module picture

LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module

$89.00



NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping* picture

NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*

$18.00