Page 1 of 3 123 LastLast
Results 1 to 10 of 29

Thread: Wireless not working on Knoppix 6.7.1

  1. #1
    Junior Member
    Join Date
    Dec 2011
    Posts
    12

    Wireless not working on Knoppix 6.7.1

    Hello,

    That's in contrast to Knoppix 6.2.1 where Wireless works OK.

    I just got delivery of Knoppix 6.7.1 DVD.
    Hardware used:
    Dell Alienware M17x laptop with
    Wireless 1529 802.11n Half MiniCard

    Knoppix 6.2.1 (kernel 2.6.32.6, udev-150) detects the wireless module,
    loads the "wl" driver as device "eth1":
    iwconfig -> eth1

    Knoppix 6.7.1 (kernel 3.0.4, udev-172) loads the "wl" driver on boot but
    iwconfig -> nothing (i.e., no wireless device detected)

    In graphics mode (LXDE, for example) the applet "Wired network connection"
    (bottom right icon), does not offer any wireless Access Points lists.
    In the only other choice to "Wired Network", "VPN connections / Configure VPN",
    it's impossible to add your wireless capability with this applet.
    Whether in the "Wireless" tab or "VPN", even if you fill in the "questionnaires"
    with your data, the "Save" button never gets activated.
    Bottom line, you can NOT connect to your Access Point or any other.

    By contrast, on the old Knoppix 6.2.1, the wireless AP's in the neighborhood
    (including mine) are listed immediately, and then establishing the connection
    presents no problems.
    But then, here, on (auto) loading the "wl" driver, an "eth1" wireless device
    is created, so you have a fighting chance to connect later on.

    NOTE
    In troubleshooting, I've tried to understand the mechanism used by Knoppix to
    detect and create wireless devices.
    Normally, one uses Udev rules (in /lib/udev/ or /etc/udev/, etc.) but you
    couldn't find anything similar in Knoppix (for eth1 or wlan).
    For example, a test wireless device, Linksys USB 802.11b, _is_ detected by
    both Knoppix's as Atmel driver module "at76c50x_usb" and a corresponding
    device "wlan0" does appear from somewhere (IMHO, the name "wlan0" is more
    appropriate than "eth1", anyway).

    Thanks

  2. #2
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    My broadcom 802.11 a/b/g uses wl & connects to eth1 ok.
    You might try g instead of n if you can.
    Last edited by utu; 12-24-2011 at 03:53 PM.

  3. #3
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    Also, FWIW, I notice this offering from Broadcom
    with a relatively recent date on it.

    http://www.broadcom.com/support/802.11/linux_sta.php

  4. #4
    Junior Member
    Join Date
    Dec 2011
    Posts
    12
    Thank you for your comments but it seems you've missed the main point of the problem (and OP).
    The "old" disk (Knoppix 6.2.1) sees the wireless card (be it a,b,g,n,x,y,z) and works with it seamlessly.
    The "new", latest disk (Knoppix 6.7.1) does not recognize the card, and concequently the wireless does not work.
    It's as simple as that. Let's not complicate it.
    Thanks again.

  5. #5
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    I note that I have 5.100.82.38-2 installed and it works ok for me, but that
    5.100.82.112-4 is an available update for broadcom-STA-common on Synaptic.
    You might also try that if you haven't already.

  6. #6
    Junior Member
    Join Date
    Dec 2011
    Posts
    12
    Hi utu,
    Thank you for your comments.
    The main, and simple idea in my OP has been missed.
    On the _same_ hardware (laptop - as described in the OP) the "old" 6.2.1 disk handles the wireless OK and seamlessly.
    The new (latest) 6.7.1 disk cannot handle wireless at all (as described in more detail in OP).
    It's as simple as that. Let's not make it any more complcated as this simple comparison, Good vs. Bad.
    The point is for somebody to resolve this contradiction or to officialy declare the 6.7.1. disk faulty and fix it.
    Thanks again.

  7. #7
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    @ Alphonsu

    I think there are a number of possibilities that something
    may be different in your 6.7.1 and 6.2.1 set-ups, such as:
    1. You might have a flawed 6.7.1 DVD;
    2. You may have disabled your wifi;
    3. You name it for some critical difference; and
    4. You may indeed have discovered a 'special' case.

    In my experience, 1 or 2 usually explain the situation.
    I'm not aware of any such case 4 for 'wl' in Knoppix 6,
    but I can't speak to the 'n' case.

    Good luck on filing a bug report.

  8. #8
    Junior Member
    Join Date
    Dec 2011
    Posts
    12
    Hi Utu,

    Let's eliminate case no 1., where by "flawed" I assume you
    imply a _physical_ problem of some sort (manufacture, shipping, etc.)

    I start with the machine down, the wireless router up and running OK.

    A. I insert the 6.2.1. disk.

    B. I boot the machine all the way.
    I connect wireless without any problems.

    C. I shut down the machine.

    D. I remove the 6.2.1 disc from the machine.

    E. I insert the 6.7.1 disk.

    F. I boot the machine all the way.
    I can NOT connect wireless no matter what I do.

    G. I shut down the machine.

    H. I remove the 6.7.1 disc from the machine

    I. I go back to step A.

    I repeat the above loop 20 times.

    I stop to write my OP where I describe the possible _technical_ differences
    between the two discs the best I can. In the process I'm hoping to convey the notion
    that I have some idea about the Linux system workings, and technical acumen in general.

    I then, repeat the loop (starting at A) until I'm blue in the face.

    Then I pause and try to pass along the idea that 6.7.1. is not bad physically
    but bad technically, which would make it possibility no 5 on your list.
    Please note that in running the 6.7.1. for some other functions,
    I haven't discovered any "flaw" that might make the disc suspect physically.
    Other than the simple (but critical for me) wireless failure the disc appears
    functional.

    Your case no 2, is not applicable (as described in the "A" loop above).
    I do not understand your case no 3 (name?), not that it matters much by now.

    As for your case no 4, there's nothing "special" here and if there's any
    "discovery", it's just that for an identical configuration the 6.7.1 disc
    does not work at all (instead of just working like the 6.2.1 one,
    without any "special" considerations). For 6.2.1., the configuration
    I've been using is (and appears to be detected by 6.2.1. as) just
    run-of-the-mill, nothing special about it.

    Thank you for your interest and comments.

    BTW, I don't know how/where to file a bug report.
    Maybe you can help. Basically the 6.7.1. is worthless for me.
    The point is for somebody to identify the technical problem and fix it.

  9. #9
    Senior Member registered user
    Join Date
    Feb 2010
    Posts
    512
    @Alphonsu

    It could be helpful to know the PCI-ID of your wireless card. The command
    Code:
    lspci -vnn
    should give you the PCI-IDs of all installed PCI devices.

  10. #10
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    Quote Originally Posted by Alphonsu View Post

    I start with the machine down, the wireless router up and running OK.

    A. I insert the 6.2.1. disk.

    B. I boot the machine all the way.
    I connect wireless without any problems.

    C. I shut down the machine.

    D. I remove the 6.2.1 disc from the machine.

    E. I insert the 6.7.1 disk.

    F. I boot the machine all the way.
    I can NOT connect wireless no matter what I do.

    G. I shut down the machine.

    H. I remove the 6.7.1 disc from the machine

    I. I go back to step A.

    I repeat the above loop 20 times.
    .
    My first test is always to look for thumbprints.
    A greasy thumbprint is enough to cause a DVD to 'be flawed'.

    You can usually see thumbprints on the shiny side of a DVD
    if you hold the DVD up to the light at the right angle.
    Clean this with isopropyl alcohol & kleenex.

    If this doesn't clear things up, then maybe the DVD is flawed
    in manufacture. If the DVD is flawed in manufacture it will
    not pass MD5 tests, and the supplier should replace it.

    Most folks I'm sure do the md5 test first. I'm lazy; almost
    all my flawed DVDs turn out to be thumbprint problems, so I
    check that first.

Page 1 of 3 123 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G picture

A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G

$11.99



A-Tech 16GB 2 x 8GB PC3-12800 Laptop SODIMM DDR3 1600 Memory RAM PC3L 16G DDR3L picture

A-Tech 16GB 2 x 8GB PC3-12800 Laptop SODIMM DDR3 1600 Memory RAM PC3L 16G DDR3L

$23.98



Team T-FORCE VULCAN Z 16GB (2 x 8GB) DDR4 3200 PC Ram Intel XMP 2.0 Memory picture

Team T-FORCE VULCAN Z 16GB (2 x 8GB) DDR4 3200 PC Ram Intel XMP 2.0 Memory

$27.99



A-Tech 16GB DDR4 2400 MHz PC4-19200 Laptop SODIMM 260-Pin 2Rx8 Memory RAM 1x 16G picture

A-Tech 16GB DDR4 2400 MHz PC4-19200 Laptop SODIMM 260-Pin 2Rx8 Memory RAM 1x 16G

$24.99



Samsung 16GB 2Rx4 PC3L-12800R DDR3-1600 1.35V ECC REG RDIMM Server Memory RAM 1x picture

Samsung 16GB 2Rx4 PC3L-12800R DDR3-1600 1.35V ECC REG RDIMM Server Memory RAM 1x

$8.50



A-Tech 16GB 2x 8GB PC3-10600 Laptop SODIMM DDR3 1333MHz 204pin Memory RAM 16G 8G picture

A-Tech 16GB 2x 8GB PC3-10600 Laptop SODIMM DDR3 1333MHz 204pin Memory RAM 16G 8G

$23.98



A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G picture

A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G

$11.99



Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3 picture

Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3

$31.95



64GB (4X 16GB) DDR3-1333 PC3-10600 Memory RAM for APPLE MAC PRO 5,1 Westmere picture

64GB (4X 16GB) DDR3-1333 PC3-10600 Memory RAM for APPLE MAC PRO 5,1 Westmere

$49.99



A-Tech 128GB 4x 32GB 2Rx4 PC4-21300R DDR4 2666 ECC REG RDIMM Server Memory RAM picture

A-Tech 128GB 4x 32GB 2Rx4 PC4-21300R DDR4 2666 ECC REG RDIMM Server Memory RAM

$131.96