Results 1 to 7 of 7

Thread: Disaster prevention.

  1. #1
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631

    Disaster prevention.

    .
    I think there is a need for some built-in protection in Knoppix 6.7
    to prevent the ruination of LiveUSBs that have been given a task that
    turns out to be catastrophic.

    What I have in mind is the bad result which occurs after starting a
    download that proves ultimately too large for the LiveUSB to accommodate.
    This ultimately fails, but also renders the LiveUSB inoperable without
    extensive repairs or re-installation.

    Couldn't there be some built-in surveillance to monitor for this
    condition and head it off with some timely warning or corrective action?

    Training the operator and/or using a larger USB are not solutions of interest.

  2. #2
    Junior Member
    Join Date
    Jun 2011
    Posts
    23
    Quote Originally Posted by utu View Post
    .
    What I have in mind is the bad result which occurs after starting a
    download that proves ultimately too large for the LiveUSB to accommodate.
    This ultimately fails, but also renders the LiveUSB inoperable without
    extensive repairs or re-installation.
    Could you be a little more elaborative.
    Does this mean that when download is done diretly on disk or on persistent image?

  3. #3
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    @ vkrishn

    For example:
    I now have about 400 MB unused on my LiveUSB with persistence.

    If I were to initiate a 700 MB download, that would proceed
    until the device was 'full' at which time I would get a
    warning 'no more room on the device'.

    At this point the LiveUSB is corrupted and will not reboot
    after shutdown. I think some some protection against this condition
    is in order.

    The few work-arounds I've tried are all harder than simply
    re-installing from a previously arranged clone copy of the LiveUSB.

  4. #4
    Junior Member
    Join Date
    Jun 2011
    Posts
    23
    I guess that means using the space on disk directly and not inside the persistent storage.
    The reason I asked, I have few usb installation wanted to be careful.

    Did you try installing Knoppix in one partition of the disk and persistent/downloads on another partition, to see if the problem still exists?

  5. #5
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    Here are two ideas:

    1. One could change IceWeasel's Edit>Preferences>General>Downloads
    FROM: 'Save files to {/home/knoppix/Downloads}'
    TO: 'Always ask always ask me where ...'

    2. If there is a 'good' answer to 'where' then one might change the
    default to that, instead of 'ask me where'.

    Leaving IceWeasel set to its download default is asking for trouble
    for those downloading into OS media of relatively limited size.

  6. #6
    Moderator Moderator
    Join Date
    Nov 2010
    Location
    Germany/ Dietzenbach
    Posts
    1,124
    At this point the LiveUSB is corrupted and will not reboot
    after shutdown.
    And you cannot reboot with cheatcode "knoppix noimage"? Of course your persistent memory is damaged, but you can use your backup.

  7. #7
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    Thanks, Werner.

    The 'noimage' approach is one means of RECOVERY that I've used.
    What I was searching for here is a means of PREVENTION.

    What with the cost of USBs coming down, there's not much
    justification anymore for 2 Gb installs like I've championed up to now.

    My favorite current configuration is a 16 Gb USB with 2 GB partition
    and the remainder formatted ext3 with kn-recombine on it.
    I can just as well shift downloads to that partition and not run
    into the 'disasters' anymore.

    Cheers.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer picture

Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer

$42.00



MITS ALTAIR 8800  Original Vintage Microcomputer picture

MITS ALTAIR 8800 Original Vintage Microcomputer

$6000.00



MITS ALTAIR 8800 88-2SIO S-100 Reproduction Board picture

MITS ALTAIR 8800 88-2SIO S-100 Reproduction Board

$35.00



MITS Altair 8800 Computer Bamboo  Reproduction Arduino Tested Working Assembled  picture

MITS Altair 8800 Computer Bamboo Reproduction Arduino Tested Working Assembled

$649.99



MITS ALTAIR 8800  Original Vintage Microcomputer  S-100   Buy It Now $5999 picture

MITS ALTAIR 8800 Original Vintage Microcomputer S-100 Buy It Now $5999

$5999.00



MITS ALTAIR 8800  Original Vintage Microcomputer with 14 boards - Buy It Now picture

MITS ALTAIR 8800 Original Vintage Microcomputer with 14 boards - Buy It Now

$9500.00



1974 Early Microcomputers by MITS Altair 8800's Ed Roberts HP-9810 Mark-8 Scelbi picture

1974 Early Microcomputers by MITS Altair 8800's Ed Roberts HP-9810 Mark-8 Scelbi

$55.00



Altair MITS 8800 CPU Card 8080A S-100 S100 replica IMSAI CP/M  picture

Altair MITS 8800 CPU Card 8080A S-100 S100 replica IMSAI CP/M 

$35.00



Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71 picture

Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71

$99.00



Altair MSAI   Douglas Electronics 11 DE Prototype Card S100 circuit board #AX44 picture

Altair MSAI Douglas Electronics 11 DE Prototype Card S100 circuit board #AX44

$69.00