-
Senior Member
registered user
Originally Posted by
ruymbeke
Hi kl522,
Here you go, I remember that Klaus mentioned once that he was using an eepc for development
and yes Knoppix 7.0.3 is using a more recent version of gcc 4.7.1-2 than the one used to compile
the kernel (gcc 4.7.1-1) as you read below. So I need to either downgrade gcc to 4.7.1-1 or use
a previous version of Knoppix which still uses that version of gcc. I would be nice to have installed
on Knoppix the correct version of gcc to recompile the kernel without complication. I guess this is a
suggestion for improvement that Klaus may consider to use on his next release.
Thanks for your help.
Best Regards,
Gilles
root@Knoppix:/# cat /proc/version
Linux version 3.4.4 (root@eeepc) (gcc version 4.7.0 (Debian 4.7.1-1) ) #14 SMP PREEMPT Sat Jun 23 20:07:21 CEST 2012
root@Knoppix:/# gcc --version
gcc (Debian 4.7.1-2) 4.7.1
Copyright (C) 2012 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
The module file can be edited manually. I have done before, after editing the module using vi, if the length of string remains, the module can be loaded. Or perhaps insmod has a force option to forcefully load a module.
-
Originally Posted by
ruymbeke
...So I need to either downgrade gcc to 4.7.1-1 or use a previous version of Knoppix...
Well Knoppix 7.0.2 is using an older version of gcc 4.6.3-7 so I will need to downgrade gcc on Knoppix 7.0.3.
So what is the easiest way to find and reinstall an older version of gcc ?
apt-get -y --reinstall install gcc-4.7=4.7.1 does not work: "E: Version '4.7.1' for 'gcc-4.7' was not found"
Best Regards,
Gilles
-
Senior Member
registered user
Originally Posted by
kl522
The module file can be edited manually. I have done before, after editing the module using vi, if the length of string remains, the module can be loaded. Or perhaps insmod has a force option to forcefully load a module.
Perhaps can try this :-
# sed -i -e 's/GCC: (Debian 4.7.1-2) 4.7.1/GCC: (Debian 4.7.1-1) 4.7.0/g' oprofile.ko
Might be faster than other methods.
-
Originally Posted by
kl522
... sed -i -e 's/GCC: (Debian 4.7.1-2) 4.7.1/GCC: (Debian 4.7.1-1) 4.7.0/g' oprofile.ko ...
Nice trick but the module still does not load because of Unknown symbols.
I may have to overlay the kernel and all the modules ...
-
Senior Member
registered user
Too bad then, I think other things are probably changed too. Maybe can still try modprobe -f.
Last edited by kl522; 08-01-2012 at 09:36 AM.
-
Originally Posted by
kl522
Too bad then, I think other things are probably changed too. Maybe can still try modprobe -f.
Hi kl522,
Nope: # depmod; modprobe -f oprofile ==> ERROR: could not insert 'oprofile': Exec format error
Thanks for your help !
Gilles
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
OWC Guardian Maximus Raid Enclosure SATA Hard Drive FireWire
$36.99
Dell EMC 092GD6 Broadcom 9305-16i LSI Quad Port 4 Port SAS RAID Controller
$84.99
UCSC-RAID-M5 CISCO 12Gb/s SAS HBA Raid Controller w/Battery & Cable
$69.99
Yottamaster 2 Bay RAID Hard Drive Enclosure USB 3.1 For 2.5" SATA HDD SSD UASP
$56.25
Dell PERC H330 PCIe 3.0 x8 RAID Storage Controller 4Y5H1 High Profile
$15.99
LSI MegaRAID 9361-8i 12Gbps PCIe 3 x8 SATA SAS 3 8 Port RAID + BBU & CacheVault
$39.00
LSI 8 Port 6Gbps PCIe 3.0 External SAS RAID Card w/ 1GB CacheVault & Low Profile
$29.00
RAID Controller Dell HYM6Y PERC H750 8GB NV Low Profile RAID Controller Card -
$26.88
Yottamaster 5 Bay RAID Hard Drive Enclosure Type-C B For 2.5" 3.5" SATA HDD SSDs
$131.59
Yottamaster 2 Bay RAID Hard Drive Enclosure USB 3.1 Type B For 3.5" SATA HDDs
$69.91