-
Senior Member
registered user
Originally Posted by
ruymbeke
Hi kl522,
Here you go, I remember that Klaus mentioned once that he was using an eepc for development
and yes Knoppix 7.0.3 is using a more recent version of gcc 4.7.1-2 than the one used to compile
the kernel (gcc 4.7.1-1) as you read below. So I need to either downgrade gcc to 4.7.1-1 or use
a previous version of Knoppix which still uses that version of gcc. I would be nice to have installed
on Knoppix the correct version of gcc to recompile the kernel without complication. I guess this is a
suggestion for improvement that Klaus may consider to use on his next release.
Thanks for your help.
Best Regards,
Gilles
root@Knoppix:/# cat /proc/version
Linux version 3.4.4 (root@eeepc) (gcc version 4.7.0 (Debian 4.7.1-1) ) #14 SMP PREEMPT Sat Jun 23 20:07:21 CEST 2012
root@Knoppix:/# gcc --version
gcc (Debian 4.7.1-2) 4.7.1
Copyright (C) 2012 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
The module file can be edited manually. I have done before, after editing the module using vi, if the length of string remains, the module can be loaded. Or perhaps insmod has a force option to forcefully load a module.
-
Originally Posted by
ruymbeke
...So I need to either downgrade gcc to 4.7.1-1 or use a previous version of Knoppix...
Well Knoppix 7.0.2 is using an older version of gcc 4.6.3-7 so I will need to downgrade gcc on Knoppix 7.0.3.
So what is the easiest way to find and reinstall an older version of gcc ?
apt-get -y --reinstall install gcc-4.7=4.7.1 does not work: "E: Version '4.7.1' for 'gcc-4.7' was not found"
Best Regards,
Gilles
-
Senior Member
registered user
Originally Posted by
kl522
The module file can be edited manually. I have done before, after editing the module using vi, if the length of string remains, the module can be loaded. Or perhaps insmod has a force option to forcefully load a module.
Perhaps can try this :-
# sed -i -e 's/GCC: (Debian 4.7.1-2) 4.7.1/GCC: (Debian 4.7.1-1) 4.7.0/g' oprofile.ko
Might be faster than other methods.
-
Originally Posted by
kl522
... sed -i -e 's/GCC: (Debian 4.7.1-2) 4.7.1/GCC: (Debian 4.7.1-1) 4.7.0/g' oprofile.ko ...
Nice trick but the module still does not load because of Unknown symbols.
I may have to overlay the kernel and all the modules ...
-
Senior Member
registered user
Too bad then, I think other things are probably changed too. Maybe can still try modprobe -f.
Last edited by kl522; 08-01-2012 at 09:36 AM.
-
Originally Posted by
kl522
Too bad then, I think other things are probably changed too. Maybe can still try modprobe -f.
Hi kl522,
Nope: # depmod; modprobe -f oprofile ==> ERROR: could not insert 'oprofile': Exec format error
Thanks for your help !
Gilles
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Vintage DEC/CLEARPOINT INC. -QRAM-2 SAB-1 1MB Q-BUS MEMORY MSV11-QA (B2)
$129.99
Vintage DEC/The Redac mini cabinet front panel Digital Equipment Corp. 19"
$269.99
VINTAGE DEC Digital RK11-D DISK CONTROL M7255 PDP 11 (B1)
$129.99
Digital Equipment Corporation DEC-2000 Vintage Keyboard - NOS NEW in Plastic
$129.95
DEC PDP 8/M PDP 8M / 4 avail / Vintage Digital Equipment Corp /Also DEC PDP 12
$5775.00
Rare Vintage DEC DIGITAL DFO3 modem with manual Powers up but UNTESTED
$69.95
Vintage Digital DEC dfo1 Acoustic Coupler modem Anderson Jacobsen Mod# A242 RARE
$195.95
Vintage DEC Digital RX 180 AB Dual 5.25" Disk Drive
$149.00
Vintage DEC Digital M8048 5013995C PDP-11 LSI 11 ROM (B3)
$79.99
DEC Digital DECMATION D100Q Z80 processor card CP/M PDP-11 (1982) B1
$119.99