Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Cannot set static IP address in Knoppix 7

  1. #1
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9

    Question Cannot set static IP address in Knoppix 7

    I often boot to Knoppix 2 (the command-line) on a network without DHCP that I administer. Up through Knoppix 6, I always set a static IP address by appending the following to /etc/network/interfaces:

    auto eth0
    iface eth0 inet static
    address 10.0.0.200
    netmask 255.255.255.0
    gateway 10.0.0.1

    Then, I would bring it up:

    ifup eth0
    portmap (I now am using "rpcbind" instead since portmap is renamed in Knoppix 7)
    rpc.statd


    This has always worked for me the in the past using pre-version 7 Knoppix and portmap. Now it works, but only for 15 seconds or so before the interface falls down. Both the presence of an IPv4 address in "ifconfig" and pinging reveal that. I can even bring eth0 up and "ping -c 40 10.0.0.1", then watch it ping successfully the first few times and get some "address not routable" error thereafter!

    I've also tried the boot cheats "nodhcp" and "ip=10.0.0.200" to no avail. Is my procedure for static IPs out of date? Or have I encountered a bug in Knoppix 7?

  2. #2
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    I haven't needed static IP for years, but this could look like some network-manager stuff to me. Tried to halt or setup the network manager?

  3. #3
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Where do I find network manager? Is that a graphical program? If so, it shouldn't affect anything in text mode (Knoppix 2).

    I did boot to the GUI and set the static IP address graphically and it worked, BTW. But that's not a solution to my problem because I still prefer text mode and should be able to change network adapter settings from there.

  4. #4
    Senior Member registered user
    Join Date
    Feb 2010
    Posts
    512
    Did you try the cheatcode 'nonetworkmanager'?

  5. #5
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    Where do I find network manager? Is that a graphical program? If so, it shouldn't affect anything in text mode (Knoppix 2).

    I did boot to the GUI and set the static IP address graphically and it worked, BTW. But that's not a solution to my problem because I still prefer text mode and should be able to change network adapter settings from there.
    All system programs may be equipped with some kind of graphical front-ends, but still operate without them, so text mode is no guarantee that a service doesn't run and keep on doing things you don't want. If you search for network-manager, you will find it is a Gnome-based service, currently configured by /etc/NetworkManager/NetworkManager.conf (on my out-of-the-box 7.0.5 DVD), with this default content:

    Code:
    [main] 
    plugins=ifupdown,keyfile  
    [ifupdown]
    managed=true
    The intention, at least, is that you can tweak this to fit your needs, but if it doesn't wotk out, you can always use the cheat code klaus2008 suggests.

  6. #6
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    The nonetworkmanager cheat works perfectly. Thank you for the workaround. Are we gaining a consensus that Network Manager is unwelcome in Knoppix 2? Does anybody else feel that this is a bug?

  7. #7
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    The nonetworkmanager cheat works perfectly. Thank you for the workaround. Are we gaining a consensus that Network Manager is unwelcome in Knoppix 2? Does anybody else feel that this is a bug?
    I wouldn't call it a bug with today's ordinary uses. To me, it is rather a typical example of simplicity for most users becoming a hassle for some more technically oriented ones. I think the config files lets us give the MAC addresses of interfaces network-manager shall keep its fingers off, so it should be a rather simple configuration operation once one knows about it.

  8. #8
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Quote Originally Posted by Capricorny View Post
    I wouldn't call it a bug with today's ordinary uses. To me, it is rather a typical example of simplicity for most users becoming a hassle for some more technically oriented ones.
    Specifically, I meant that Network Manager is helpful to most users (who boot to the GUI). I only meant that it is unwelcome in Knoppix 2 (the text-mode). Since the default content of /etc/NetworkManager/NetworkManager.conf that you pasted above doesn't have an obvious spot for a static IP address, subnet mask, and default gateway, I find /etc/network/interfaces to be the obvious way to establish a static IP address in text mode. Therefore, I don't welcome Network Manager when booted to text mode. Furthermore, I believe Knoppix 7's command line should behave as close to Knoppix 6's command line as possible. New features shouldn't break beloved commands.

  9. #9
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    Specifically, I meant that Network Manager is helpful to most users (who boot to the GUI). I only meant that it is unwelcome in Knoppix 2 (the text-mode). Since the default content of /etc/NetworkManager/NetworkManager.conf that you pasted above doesn't have an obvious spot for a static IP address, subnet mask, and default gateway, I find /etc/network/interfaces to be the obvious way to establish a static IP address in text mode. Therefore, I don't welcome Network Manager when booted to text mode. Furthermore, I believe Knoppix 7's command line should behave as close to Knoppix 6's command line as possible. New features shouldn't break beloved commands.
    Yes, in your use situation, the case is pretty clear. But I can imagine that KK is rather reluctant to tie basic services to the graphical mode, which is why he has opted for a cheatcode off-switch instead. And when you have told networkmanager not to manage an interface, I would think the other configuration tools work or could relatively easily be made to do so.

    I completely agree with respect to command line behavior.

  10. #10
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Update: I have solved my static IP troubles by switching to Debian Live Rescue. It's like stepping into last decade, but the stability is second to none.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Juniper EX4600-40F-AFI 24 SFP+/SFP Ports 4 QSFP+ Ports Dual AC Switch picture

Juniper EX4600-40F-AFI 24 SFP+/SFP Ports 4 QSFP+ Ports Dual AC Switch

$1300.00



Juniper SRX1500-SYS-JB-AC SRX1500 Services Gateway-Dual Power JPSU-400W-AC picture

Juniper SRX1500-SYS-JB-AC SRX1500 Services Gateway-Dual Power JPSU-400W-AC

$1784.00



Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord picture

Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord

$43.95



Juniper Networks EX4300-48T 48 Port Gigabit 4 QSFP 40G 2xPSU AFO Network Switch picture

Juniper Networks EX4300-48T 48 Port Gigabit 4 QSFP 40G 2xPSU AFO Network Switch

$89.00



JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER picture

JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER

$210.00



Juniper EX3400-48P 48-Ports PoE+ 4x SFP+ and 2x QSFP+ Managed Switch Tested picture

Juniper EX3400-48P 48-Ports PoE+ 4x SFP+ and 2x QSFP+ Managed Switch Tested

$205.00



Juniper QFX5100-48S-3AFO Switch 48 x 10Gb SFP+, 6x QSFP 40GE, Dual AC Power picture

Juniper QFX5100-48S-3AFO Switch 48 x 10Gb SFP+, 6x QSFP 40GE, Dual AC Power

$499.00



Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord picture

Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord

$54.99



Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch picture

Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch

$40.23



JUNIPER EX4550-32F-AFO 32-PORT ETHERNET SWITCH 2x POWER SUPPLY - TESTED picture

JUNIPER EX4550-32F-AFO 32-PORT ETHERNET SWITCH 2x POWER SUPPLY - TESTED

$299.99