-
Senior Member
registered user
Frequent wifi disconnects & re-connects
.
My laptop has a built-in wifi, rated for class a/b/g and n.
I have two routers, one from Verizon which is rated for class a/b/g, and connects with WEP.
the other is a Belkin rated for classes g and n, and connects with WAP.
I have nominally 15 Mb/s broadband, and 15 internet-near-neighbors, mostly Verizon subscribers
I would guess from the routers' designations. My routers show 2 to 4 bars, neighbors show 1 or 2.
My laptop usually connects to either of my routers in a few seconds, with the WAP connection taking
just slightly longer.
Over an eight-hour period of occasional, but infrequent on-line use of a given internet
connection, the Verizon router remains connected continuously, whereas
over a comparable eight-hour period, the Belkin
router has 145 disconnect-and-reconnects, averaging about every 3.3 minutes. The disconnected
period for the Belkin router is usually only about two seconds long.
If I were not alarmed by all the print-out on /var/log/syslog for the Belkin case, I might not
be aware of much diffence in browsing performance between the two routers, excepting only the
occasional time there is a noticeable lag in surfing to a new internet address, presumably
waiting for one of the two-second-reconnects to complete.
Any thoughts on what might be troubling my Belkin router would be appreciated.
Last edited by utu; 01-08-2013 at 08:02 PM.
-
Senior Member
registered user
Have you tried changing the channel on the Belkin ? Does the output of
Code:
iwlist <interface>scanning
show other wireless on the same channel, and what does the output of suggest as far as link quality etc. ?
-
Senior Member
registered user
Greetings, Rusty & thanks for your comments:
iwlist gives the following info:
Code:
iwlist wlan0 scanning | grep -A 3 Freq > iwlist.txt
and some << marginal notes added
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-34 dBM <- sometimes 4 bars
Quality=45/70 Signal level=-65 dBm <- other times 2 bars
Encryption key:on
ESSID:"belkin.594" <- my 'n' router
--
Frequency:2.462 GHz (Channel 11)
Quality=35/70 Signal level=-75 dBm <- 2 bars, usually
Encryption key:on
ESSID:"WARnet" <- a neighbor
--
Frequency:2.462 GHz (Channel 11)
Quality=21/70 Signal level=-89 dBm
Encryption key:on
ESSID:"2P5U7"
--
Frequency:2.462 GHz (Channel 11)
Quality=42/70 Signal level=-68 dBm <- 2 bars, usually
Encryption key:on
ESSID:"BUXL3" <- my 'g' router
--
Frequency:2.437 GHz (Channel 6)
Quality=26/70 Signal level=-84 dBm
Encryption key:on
ESSID:"woozle"
--
Frequency:2.462 GHz (Channel 11)
Quality=23/70 Signal level=-87 dBm
Encryption key:on
ESSID:"EJIM2"
--
Frequency:2.437 GHz (Channel 6)
Quality=25/70 Signal level=-85 dBm
Encryption key:on
ESSID:"NYM3B"
--
Frequency:2.412 GHz (Channel 1)
Quality=23/70 Signal level=-87 dBm
Encryption key:on
ESSID:"E5JA2"
--
Frequency:2.462 GHz (Channel 11)
Quality=20/70 Signal level=-90 dBm
Encryption key:on
ESSID:"418A5"
--
Frequency:2.412 GHz (Channel 1)
Quality=31/70 Signal level=-79 dBm
Encryption key:on
ESSID:"Amped_SR"
--
Frequency:2.437 GHz (Channel 6)
Quality=24/70 Signal level=-86 dBm
Encryption key:on
ESSID:"706D1"
--
Frequency:2.412 GHz (Channel 1)
Quality=22/70 Signal level=-88 dBm
Encryption key:on
ESSID:"K7964"
--
Frequency:2.462 GHz (Channel 11)
Quality=20/70 Signal level=-90 dBm
Encryption key:on
ESSID:"LNSL7"
--
Frequency:2.462 GHz (Channel 11)
Quality=20/70 Signal level=-90 dBm
Encryption key:on
ESSID:"UUEL3"
--
Frequency:2.412 GHz (Channel 1)
Quality=23/70 Signal level=-87 dBm
Encryption key:on
ESSID:"T3P32"
--
Frequency:2.412 GHz (Channel 1)
Quality=22/70 Signal level=-88 dBm
Encryption key:on
ESSID:""
--
iwconfig adds to this only that 'Power Management is Off'.
--
I'm not sure I have a channel choice with n mode.
-
Senior Member
registered user
You should be able to log on to the Belkin interface and change the channel to one of the unused ones, 9 might be a good choice, and see if it improves things.
This is a rudimentary introduction into wireless frequencies: http://en.wikipedia.org/wiki/List_of_WLAN_channels.
-
Senior Member
registered user
I'll look into this.
FYI, I notice in my neighborhood there are 5 users on Channel 1,
3 users on Channel 6, and 4 users on Channel 11. The other channels are unused.
-
Senior Member
registered user
Bummer.
I'm all alone on channel 4 now, but the disconnects persist.
Problem serious enough to show on the cpu monitor, and give halting text display.
-
Senior Member
registered user
You could use wireshark I suppose to see if there is a lot of negotiation going on between the laptop and the Belkin, or try a connecting to a different N router to see if the problem occurs. Do other N devices connect ok to the Belkin ? Can you restrict the Belkin to N only?
-
Senior Member
registered user
Klaus K offered the following advice in this situation.
In a crowded environment, sometimes it helps to
1. Reduce (!) Antenna power, so the access point enhances the signal,
2. Fix the data rate in order to avoid renegotiations.
sudo iwconfig wlan0 txpower 5mW
sudo iwconfig wlan0 rate 54M
You can try different values, of course.
The most important is to avoid an "auto" setting, since this triggers renegotiations.
Regards
-Klaus
I think the combination of Klaus's suggestion and Rusty's has greatly improved the
situation here. While waiting to see if this holds, I'll research Wireshark.
Thanks, Rusty.
-
Senior Member
registered user
Status update:
With both using Klaus K's and Rusty's suggestions together, my
broadband situation is now (more) tolerable. My cpu is usage way down, but
with n-mode router and n-mode laptop, I am still getting about a page
a minute of /var/log/syslog showing two-second re-acquisitions every
one or two minutes.
Broadband speed tests usually show a generous broadband download number.
-
Senior Member
registered user
utu, just from my own experience:
When such problems can not be fully related to known bugs or the operation setting, most of the time they have been due to hardware failures/glitches. In hindsight, I have tolerated way too much reconnecting, restarting etc instead of just putting in a new piece of hardware. (In one case with fibre last summer, it turned out the new receiver was grilled, signals were too strong at my location and had to be dampened.) Have you tried with an alternative router to see if the problems persist?
To me, it might seem like your measures have speeded up reconnection, the fallout being less influenced?
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
![DELL PowerEdge R630 8SFF Server 2x E5-2680v4 2.4GHz =28 Cores 128GB H730 4xRJ45 picture](/store/img/qfQAAOSw9XRklkNR/s-l225//DELL-PowerEdge-R630-8SFF-Server-2x-E5-2680v4-2-4GH.jpg)
DELL PowerEdge R630 8SFF Server 2x E5-2680v4 2.4GHz =28 Cores 128GB H730 4xRJ45
$339.00
![Dell PowerEdge R630 Server 2x E5-2680 V4 = 28 Cores S130 32GB RAM NEW 480GB SSD picture](/store/img/CaAAAOSwEjBmj~ML/s-l225//Dell-PowerEdge-R630-Server-2x-E5-2680-V4-28-Cores-.jpg)
Dell PowerEdge R630 Server 2x E5-2680 V4 = 28 Cores S130 32GB RAM NEW 480GB SSD
$256.99
![Dell Poweredge R730xd LFF 14-Bay 2U Server | Choose Your CPU & RAM Config picture](/store/img/CdkAAOSwY0BmYMoF/s-l225//Dell-Poweredge-R730xd-LFF-14-Bay-2U-Server-Choose-.jpg)
Dell Poweredge R730xd LFF 14-Bay 2U Server | Choose Your CPU & RAM Config
$454.99
![Dell Poweredge R730xd 2x E5-2660 v3 2.6ghz / 64gb / H730 / 24x Trays / 2x 750w picture](/store/img/mH0AAOSwCvxmK9Zr/s-l225//Dell-Poweredge-R730xd-2x-E5-2660-v3-2-6ghz-64gb-H7.jpg)
Dell Poweredge R730xd 2x E5-2660 v3 2.6ghz / 64gb / H730 / 24x Trays / 2x 750w
$344.99
![Dell PowerEdge R630 Server 2x E5-2640v3 2.60Ghz 16-Core 64GB H330 picture](/store/img/ZD0AAOSwm41mOZYw/s-l225//Dell-PowerEdge-R630-Server-2x-E5-2640v3-2-60Ghz-16.jpg)
Dell PowerEdge R630 Server 2x E5-2640v3 2.60Ghz 16-Core 64GB H330
$182.65
![HP ProLiant DL360 G9 Server 2x E5-2690v3 2.60Ghz 24-Core 256GB P440ar picture](/store/img/HBEAAOSwasRkPVvF/s-l225//HP-ProLiant-DL360-G9-Server-2x-E5-2690v3-2-60Ghz-2.jpg)
HP ProLiant DL360 G9 Server 2x E5-2690v3 2.60Ghz 24-Core 256GB P440ar
$302.90
![Dell Poweredge R630 Server 2x E5-2620 V4 =16 Cores | S130 | 32GB RAM | 2x trays picture](/store/img/GAcAAOSw9Q1mGSZW/s-l225//Dell-Poweredge-R630-Server-2x-E5-2620-V4-16-Cores-.jpg)
Dell Poweredge R630 Server 2x E5-2620 V4 =16 Cores | S130 | 32GB RAM | 2x trays
$171.99
![Lenovo ThinkServer TS140 Xeon E3-1225v3 3.20GHz 16GB RAM Tower Server Needs HDD picture](/store/img/vSgAAOSwEp5maJ3a/s-l225//Lenovo-ThinkServer-TS140-Xeon-E3-1225v3-3-20GHz-16.jpg)
Lenovo ThinkServer TS140 Xeon E3-1225v3 3.20GHz 16GB RAM Tower Server Needs HDD
$99.99
![DELL PowerEdge R730 16SFF Server 2x E5-2680v4 2.4GHz =28 Cores 64GB H730 4xRJ45 picture](/store/img/HgEAAOSwQh5k1YNe/s-l225//DELL-PowerEdge-R730-16SFF-Server-2x-E5-2680v4-2-4G.jpg)
DELL PowerEdge R730 16SFF Server 2x E5-2680v4 2.4GHz =28 Cores 64GB H730 4xRJ45
$317.00
![Cisco UCS C240 M4 2U Server w/ 2x E5-2680v4, NO RAM picture](/store/img/Je8AAOSwIcdmTgJF/s-l225//Cisco-UCS-C240-M4-2U-Server-w-2x-E5-2680v4-NO-RAM.jpg)
Cisco UCS C240 M4 2U Server w/ 2x E5-2680v4, NO RAM
$39.99