-
Multiple Video Cards and getting xorg.conf set up properly for multihead
I've always wanted to run dual video cards with linux. However, every time I try it I get really frustrated (because I don't really know what I'm doing with regards to X) and give up.
I wish it were as easy as windows, where you just click on a few dialogs and things come up magically. I struggled with this so mightily I could just really say #%@#$#@$ and be happy with dualhead on a single card. Fiddling with /etc/X11/xorg.conf and trying to start X and trying over and over again. I had to go back to the internet many times to look for more ideas to try... This is so 1980s with manual configuration files and very little feedback as to what's going wrong. And I like to think that I'm fairly techno savvy.
Knoppix works awesomely with a single video card with dual heads. ARandR is marvelous and "just works." However, things get tricky when you want to run multiple video cards.
So I've got two cards: a geforce 7300 pci-e card with 2 heads and a geforce mx420 pci card with vga.
Knoppix actually detects both perfectly and brings up a text display on both cards. The hard part is configuring the /etc/X11/xorg.conf file.
Here's what "works for me":
lspci
1:00.0 VGA compatible controller: NVIDIA Corporation G72 [GeForce 7300 LE] (rev a1)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5754 Gigabit Ethernet PCI Express (rev 02)
04:02.0 VGA compatible controller: NVIDIA Corporation NV17 [GeForce4 MX 420] (rev a3)
card0 is the geforce 7300LE
card1 is the geforce mx420
so I need to know the actual outputs of each card, and you can see the pci BusID address by looking at /sys/class/drm
knoppix@Microknoppix:~$ ls -l /sys/class/drm
total 0
lrwxrwxrwx 1 root root 0 Nov 23 22:29 card0 -> ../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card0-DVI-I-1 -> ../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0/card0-DVI-I-1
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card0-TV-1 -> ../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0/card0-TV-1
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card0-VGA-1 -> ../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0/card0-VGA-1
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card1 -> ../../devices/pci0000:00/0000:00:1e.0/0000:04:02.0/drm/card1
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card1-TV-2 -> ../../devices/pci0000:00/0000:00:1e.0/0000:04:02.0/drm/card1/card1-TV-2
lrwxrwxrwx 1 root root 0 Nov 24 05:26 card1-VGA-2 -> ../../devices/pci0000:00/0000:00:1e.0/0000:04:02.0/drm/card1/card1-VGA-2
and
knoppix@Microknoppix:~$ cat /sys/class/drm/*/status
disconnected
disconnected
connected
connected
connected
so it's VGA-1 on card0, VGA-2 and TV-2 on card1 are connected
and excerpts from my xorg.conf from /etc/X11/xorg.conf
# /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
Option "Xinerama" "true"
Option "Clone" "off"
Option "AIGLX" "true"
EndSection
Section "Monitor"
Identifier "Monitor0"
ModelName "Generic Monitor"
EndSection
Section "Monitor"
Identifier "Monitor1"
ModelName "Generic Monitor"
EndSection
Section "Device"
Identifier "Card1"
Driver "nouveau"
VendorName "All"
BoardName "All"
BusID "PCI:4:2:0"
Option "ZaphodHeads" "VGA-2"
EndSection
Section "Device"
Identifier "Card0"
Driver "nouveau"
VendorName "All"
BoardName "All"
BusID "PCI:1:0:0"
Option "ZaphodHeads" "VGA-1"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card1"
Monitor "Monitor0"
EndSection
Section "Screen"
Identifier "Screen1"
Device "Card0"
Monitor "Monitor1"
EndSection
I got another monitor and wanted to hook it up to card 0, so I added a few things:
Section "ServerLayout"
Identifier "X.org Configured"
Option "Xinerama" "on"
Option "Clone" "off"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
Screen 2 "Screen2" RightOf "Screen1" #added screen 2 here
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
Option "AllowEmptyInput" "off"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Option "ZaphodHeads" "VGA-1"
Identifier "Card0"
Driver "nouveau"
BusID "PCI:1:0:0"
Screen 0
EndSection
Section "Device"
Option "ZaphodHeads" "DVI-I-1"
Identifier "Card0-DVI"
Driver "nouveau"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen2"
Device "Card0-DVI"
Monitor "Monitor1"
EndSection
note that if you set the wrong screen number (like Screen 1 instead of Screen 0) in the Section "Device" the configuration will not work and you will get a message like this in /var/log/Xorg.0.log
Xorg Screen 1 deleted because of no matching config
This is an easy fix, just swap the screen numbers until it works. So I tried Screen 0 for Section "Device" Identifier Card0-DVI", and it didn't work so I went with Screen 1 which did. Note that this Screen number in the Section "Device" refers to the screens "internally numbered" for each head on a given card, and does not have anything to do with the Section "Screen". That was something I found a bit confusing.
You can omit the Screen number in the Section "Device" but it will only display a clone of the other head on the card.
a few tips and tricks:
boot with "knoppix 2" and then use
X -configure (to have Xorg try to generate an autoconfiguration, it puts a heck of a lot of crud into the file, but it does show you some ideas and structure. I think it made 7 different devices and screens, duplicating the card 3 or 4 times for different drivers)
X -config <filename> (to have Xorg use a different file location than /etc/X11/xorg.conf)
X -retro (to test your xorg.conf with a checkerboard background and the retro X pointer because when you launch X, the background is black and there's no mouse pointer)
and also the CTRL+ALT+BACKSPACE keystroke to kill the X server.
less /var/log/Xorg.0.log to see any error messages
less /var/log/Xorg.0.log | grep EE (to see any error events)
So I'd do a bunch of edits with "emacs /etc/X11/xorg.conf", then save the changes, and then launch "X -retro" to test them out. I'd exit the X server with CTRL+ALT+BACKSPACE. Once I'd get a setup that would work, I'd save it and reboot knoppix normally. (and I removed the line at the top of xorg.conf that tells knoppix to autogenerate this file on reboot.) Also note that I'm using knoppix with a "persistent" imagefile so /etc/X11/xorg.conf persists through reboots.
You can also do the editing within X-windows if you're brave, just emacs /etc/X11/xorg.conf from a terminal window, then CTRL+ALT+BACKSPACE which will kill and relaunch the X session, reading in your new xorg.conf.
My full xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Option "Xinerama" "on"
Option "Clone" "off"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
Screen 2 "Screen2" RightOf "Screen1"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
Option "AllowEmptyInput" "off"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "built-ins"
EndSection
Section "Module"
Load "dbe"
Load "dri"
Load "dri2"
Load "extmod"
Load "glx"
Load "record"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Option "ZaphodHeads" "VGA-1"
Identifier "Card0"
Driver "nouveau"
BusID "PCI:1:0:0"
Screen 0
EndSection
Section "Device"
Option "ZaphodHeads" "DVI-I-1"
Identifier "Card0-DVI"
Driver "nouveau"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Device"
Option "ZaphodHeads" "VGA-2"
Identifier "Card1"
Driver "nouveau"
BusID "PCI:4:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card1"
Monitor "Monitor0"
EndSection
Section "Screen"
Identifier "Screen1"
Device "Card0"
Monitor "Monitor1"
EndSection
Section "Screen"
Identifier "Screen2"
Device "Card0-DVI"
Monitor "Monitor1"
EndSection
Section "DRI"
Mode 0666
EndSection
-
I thought I had this multiple video card thing figured out... and so I tried a radeon 7000 PCI with my geforce 7300 PCI-E and couldn't get it work. And then I tried a geforce 6200 PCI with a geforce 7300 PCI-E and couldn't get that to work properly. I could actually get all 4 monitors to come up with "X -retro" with a heck of a lot of fiddling on xorg.conf... but it wouldn't work properly with the full X session GUI. I guess that getting the geforce 7300 PCI-E to work with a Geforce MX420 PCI was a lucky combination. Too bad. I really really wanted it to work.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell PowerEdge R640 Server 2x Gold 6150 2.70Ghz 36-Core 256GB 2x 960GB SSD H730P
$1737.25
Dell R740XD 24SFF 12 NVMe 2.8Ghz 56-C 192GB H730P 2x10G+2x1G NIC 2x1100W Rails
$5040.07
Dell R740XD 24SFF+4SFF 2.8Ghz 56-C 256GB H740P 10G SFP+ NIC 2x1100W 12x Trays
$4704.08
Dell PowerEdge R740xd Server 2x Gold 6140 2.30Ghz 36-Core 512GB H330
$2194.80
INTEL XEON GOLD 6148 20 Core SR3B6 2.4GHZ 27.5MB Processor @24
$99.99
Intel Xeon Gold 6138 2.0GHz 27.5MB 20-Core 125W LGA3647 SR3B5
$46.00
Intel Xeon E5-2697 V4 2.30 GHz 18C 2011-3 2400MHz 45MB 145W SR2JV CPU Processor
$49.99
Intel Xeon E5-2690V2 3.00GHz 10-Core (SR1A5) Processor CPU READ DESCRIPTION
$12.00
HP Workstation Z640 2x Xeon E5-2623V4 32GB Ram 512 SSD Quadro K420 Linux GA
$243.59
Dell Precision 5810 Tower Intel Xeon E5-1603v3 2.8GHz 8GB RAM 500GB HDD W10P GPU
$129.99