Using: '/.config/.../autostart' does not work?
.
Greetings, All.
With earlier Knoppix 6s and 7s, I became accustomed to making
small changes to certain system files to achieve some modest LiveUSB
'improvements'. For some reason, I seem to be locked out of the
ability to just go in and modify these files as I used to do.
Two specific files that are resisting my efforts are:
/etc/xdg/lxsession/LXDE/autostart (I want to add iceweasel), and
/etc/syslog-knoppix.conf (I want to add /var/log/syslog)
What has changed that I should know about? TIA.
Using: '/.config/.../autostart' does not work?
Last edited by philo; 08-18-2014 at 10:39 AM.
# startup.desktop
[Desktop Entry]
Name=Startup
Exec="iceweasel"
Icon=
Type=Application
(Adapted from an old Klaus2008 posting)
Did you see this posting by Werner in August 2013:
http://knoppix.net/forum/showthread....l=1#post129773
Greetings, again philo.
I hadn't seen this before, but I think Werner is right here, as usual.
Without a specific page target the results are a little erratic on just what the browser will display;
often, but not always with its own 'oops' message.
I had almost come to Werner's conclusion on my own.
Thanks again for your help.
.
1. I have tamed Compiz to my satisfaction for now.
2. Given that, my Post #4 here now adequately fills my autostart needs.
3. I haven't a clue on how to get syslog back, and Werner's
old syslog solution doesn't work any more, either.
I haven't a clue on how to get syslog back, ..Greetings WernerCode:su mv /etc/syslog-knoppix.conf /etc/syslog-knoppix.conf_orig aptitude install anacron ln -s /usr/sbin/rsyslogd /sbin/syslogd reboot
Greetings, Werner, and thanks.
Using Knoppix 7.2 and previous versions of Knoppix, I created a
few useful utility functions to time (or count) things relative to time at boot
using syslog. Each syslog line entry begins with a character group
formatted similar to a date function response formatted in
hours, minutes and seconds since the time syslog started at boot.
For examples:
What does a typical anacron or cron print-out (or line of output) look like?Code:# Parts of my ~/.bashrc in Knoppix 7.2: alias 'Syslog=less /var/log/syslog' # requires syslog at.Start(){ # echo time at Start (requires Syslog) echo -e "at Start: \c"; Syslog | grep restart | awk '{ print $3 }' } Boot.Time(){ # Seconds to browser on-line (requires Syslog) echo -e "Online at: \c"; Syslog | grep avahi | awk '{ print $3 }' at.Start } Disconnects() { # Wifi disconnects since boot (requires Syslog) echo -e "Time now: \c"; date | awk '{ print $4 }' at.Start echo -e "Wifi disconnects: \c"; Syslog | grep -c disconnecting }
Can you give us a Screenshot?
Last edited by utu; 08-19-2014 at 02:48 PM.
'/usr/sbin/rsyslogd' succeeds '/sbin/syslogd'. But '/etc/init.d/knoppix-autoconfig' still uses '/sbin/syslogd'; therefore I suggest the use of a symlink. Perhaps in a new Knoppix version this will no longer work.
I think your bashrc will work as until now.
Cron or anacron have no print-out. With cron you can define jobs and their execution time to logrotate the output of the logfiles; this will prevent an overflow of '/var/log'. If you doesn't have a server which will run all over the time, you need anacron. It will make up these cron jobs, which could not be carried out because the computer has been shut off at the defined execution time.
ARUBA J9772A 2530-48G PoE+ 48 PORT ETHERNET SWITCH W/ RACK EARS J9772-60301
$299.95
HPE ARUBA 2530-24G J9773A PoE+ 24-PORT GIGABIT ETHERNET SWITCH J9773-60201
$209.95
Fortinet FortiSwitch FS-124D-POE 24 Port Gigabit Ethernet Switch UNREGISTERED
$99.97
Cisco SG300-52-Port Gigabit Managed Rack Mountable Network Switch
$44.95
Netgear 16-Port Gigabit Ethernet Switch GS316 Unmanaged
$10.00
NETGEAR GS305300PAS 5 Port Gigabit Ethernet Unmanaged Switch
$15.99
Netgear ProSafe FS116 Blue Fast Ethernet 16-Port 10/100 Unmanaged Desktop Switch
$12.80
TP-Link TL-SG108PE 8-port Gigabit Easy Smart PoE+ Swith w/ 4-port PoE - Sealed
$49.50
HP JG937A Flexnetwork 5130-48G PoE+ 48-Port Gigabit Network Switch
$59.99
Brocade ICX 7250-48 48-Port Gigabit Ethernet Network Switch | ICX7250-48-2X10G
$84.95