Using: '/.config/.../autostart' does not work?
.
Greetings, All.
With earlier Knoppix 6s and 7s, I became accustomed to making
small changes to certain system files to achieve some modest LiveUSB
'improvements'. For some reason, I seem to be locked out of the
ability to just go in and modify these files as I used to do.
Two specific files that are resisting my efforts are:
/etc/xdg/lxsession/LXDE/autostart (I want to add iceweasel), and
/etc/syslog-knoppix.conf (I want to add /var/log/syslog)
What has changed that I should know about? TIA.
Using: '/.config/.../autostart' does not work?
Last edited by philo; 08-18-2014 at 10:39 AM.
# startup.desktop
[Desktop Entry]
Name=Startup
Exec="iceweasel"
Icon=
Type=Application
(Adapted from an old Klaus2008 posting)
Did you see this posting by Werner in August 2013:
http://knoppix.net/forum/showthread....l=1#post129773
Greetings, again philo.
I hadn't seen this before, but I think Werner is right here, as usual.
Without a specific page target the results are a little erratic on just what the browser will display;
often, but not always with its own 'oops' message.
I had almost come to Werner's conclusion on my own.
Thanks again for your help.
.
1. I have tamed Compiz to my satisfaction for now.
2. Given that, my Post #4 here now adequately fills my autostart needs.
3. I haven't a clue on how to get syslog back, and Werner's
old syslog solution doesn't work any more, either.
I haven't a clue on how to get syslog back, ..Greetings WernerCode:su mv /etc/syslog-knoppix.conf /etc/syslog-knoppix.conf_orig aptitude install anacron ln -s /usr/sbin/rsyslogd /sbin/syslogd reboot
Greetings, Werner, and thanks.
Using Knoppix 7.2 and previous versions of Knoppix, I created a
few useful utility functions to time (or count) things relative to time at boot
using syslog. Each syslog line entry begins with a character group
formatted similar to a date function response formatted in
hours, minutes and seconds since the time syslog started at boot.
For examples:
What does a typical anacron or cron print-out (or line of output) look like?Code:# Parts of my ~/.bashrc in Knoppix 7.2: alias 'Syslog=less /var/log/syslog' # requires syslog at.Start(){ # echo time at Start (requires Syslog) echo -e "at Start: \c"; Syslog | grep restart | awk '{ print $3 }' } Boot.Time(){ # Seconds to browser on-line (requires Syslog) echo -e "Online at: \c"; Syslog | grep avahi | awk '{ print $3 }' at.Start } Disconnects() { # Wifi disconnects since boot (requires Syslog) echo -e "Time now: \c"; date | awk '{ print $4 }' at.Start echo -e "Wifi disconnects: \c"; Syslog | grep -c disconnecting }
Can you give us a Screenshot?
Last edited by utu; 08-19-2014 at 02:48 PM.
'/usr/sbin/rsyslogd' succeeds '/sbin/syslogd'. But '/etc/init.d/knoppix-autoconfig' still uses '/sbin/syslogd'; therefore I suggest the use of a symlink. Perhaps in a new Knoppix version this will no longer work.
I think your bashrc will work as until now.
Cron or anacron have no print-out. With cron you can define jobs and their execution time to logrotate the output of the logfiles; this will prevent an overflow of '/var/log'. If you doesn't have a server which will run all over the time, you need anacron. It will make up these cron jobs, which could not be carried out because the computer has been shut off at the defined execution time.
Juniper EX4600-40F-AFI 24 SFP+/SFP Ports 4 QSFP+ Ports Dual AC Switch
$1300.00
Juniper SRX1500-SYS-JB-AC SRX1500 Services Gateway-Dual Power JPSU-400W-AC
$1784.00
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord
$43.95
Juniper Networks EX4300-48T 48 Port Gigabit 4 QSFP 40G 2xPSU AFO Network Switch
$89.00
Juniper EX4600-40F-AFI 24 SFP+/SFP Ports 4 QSFP+ Ports Dual AC Switch
$999.00
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$210.00
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$40.10
Juniper QFX5100-48S-3AFO Switch 48 x 10Gb SFP+, 6x QSFP 40GE, Dual AC Power
$499.00
JUNIPER EX4550-32F-AFO 32-PORT ETHERNET SWITCH 2x POWER SUPPLY - TESTED
$299.99
Juniper EX2300-48P PoE+ Switch 48x 1GbE & 4 SFP+/SFP 10G uplinks, Tested
$289.00