Try this
edit your /etc/resolv.conf file
only have typed inCode:pico /etc/resolv.conf
this is a DNS server for qwest i believeCode:nameserver 4.2.2.2
then save the file (ctrl+X)
now try to ping yahoo.com and see if it works
except the box I am connected to. This is true with KPPP and with pon. Each has been configured independently. After several attempts, I replaced the /etc/resolv.conflict file with one from a working RH installaation, but no go.
I reset all the timeouts to maxima. PPPStatus reports "stalls" without end except when pinging the ISP box I am connected to. No other IP traffic is sent.
The same ISP, number and modem work fine under Windows, and works fine under RH-6.2 on my old box, so the prob is neither with my hardware nor with the ISP.
Can someone shed some light on this prob? What am I overlooking? Or is Knoppix 060603 (3.2) flawed in some way? Should I try another build?
Try this
edit your /etc/resolv.conf file
only have typed inCode:pico /etc/resolv.conf
this is a DNS server for qwest i believeCode:nameserver 4.2.2.2
then save the file (ctrl+X)
now try to ping yahoo.com and see if it works
Did it. No change in behavior.
Originally Posted by adamm
dial up to the internet and type in
and patse the output hereCode:route -n
under "Flags" you should have one that reads UG which is your default gateway, this should be present or you won't be able to get to the internet
Can't paste -- can't connect to the internet I am on my old box (RH-6.2). The two are not yet connected., so I have to type in what's on the other monitor. Hope I get it right!Originally Posted by adamm
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
66.81.235.197 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.0.254 .0.0.0.0 UG 0 0 0 eth0
Hope that helps.
However, in playing with wvdial ( a common between Knoppix and Red Hat -- RP3 is just a frontend for wvdial) I discovered what my feeling was all along: the password is not being forwarded correctly.
When invoking wvdial (after setting up /etc/wvdial.conf with wvdialconf) I get a failure with the message that "no valid passowrd" was found. It is in /etc/wvdial in plain sight and plain text.
What else leads me to suspect a password-forwarding problem is that although I can connect with XISP under RedHat using PAP/CHAP, RH's wvdial demands I connect with CHAP, which fails with a SIGHUP in Knoppix. I can get a pseudo connection with KPPP using PAP/CHAP under Knoppix' KPPP or pon apparently, but using CHAP gives a hangup to my password in both, although only wvdial warns me of not finding a password.
Stumps me.
Or I am not understanding something basic.
The Subject says it all. Although I did a MD5 sum check on the ISO I downloaded, I copied the ISO from one hard disk to another, then installed the target hard disk on a new box, burned the ISO, but didn't notice a filesize mismatch between the target ISO and the source. 16+ MB are missing! Damn Windows!
But I digress. This was not Knoppix' problem. It was all mine.
SUN Blade X6250 Server 8GB RAM DUAL PROCESSORS 594-4531-01
$109.99
CISCO 5108 Blade Server Chassis N20-C6508
$200.00
Dell PowerEdge M620 0F9HJC Blade Server 2*E5-2670 2.60GHz 192GB RAM 2*300GB SAS
$103.99
Dell PowerEdge M630 Blade Server 1x Xeon E5-2630 v4 CPU / Motherboard P/N 0R10KG
$69.99
HP ProLiant BL460c G9 (Gen9) 2x E5-2670V3 12 Core 3.1GHz No Ram or No Drives
$59.98
DELL M630 BLADE SERVER x2 XEON E5-2660V3 @ 2.6GH H730 PERC HDD CADDIES 16GB FC
$50.00
Dell PowerEdge C6400 Blade Server Chassis w/ 2x 2400W PSUs - Preproduction Model
$349.00
Dell PowerEdge MX7000 CTO Blade 8 slot 7U Chassis 6x 3000W 2x MX9002m
$2399.00
Dell PowerEdge M620 Blade Server
$39.99
Cisco UCS 5108 Blade Server Chassis Enclosure N20-C6508 4x PSU 8x Fans 2x Fabric
$139.99