did you use CD attached to graphic card and new screen? First connect old screen and install graphics card and make sure its working fine. After this you screen should work fine as well so do this and tell me results.
I replaced my original graphic card (ASUS EAH3850 512 MB DDR3) with a new (ASUS TURBO GTX1060 6GB) in my desktop.
Probably, this HW replacement caused my problem.
Start of Knoppix looks correctly. There are no errors / warnings in console.
But, after starting a graphical interface, there is a black screen, and monitor shows only a message:
"The current input timing is not supported by monitor display. Please change your input timing to 1920x1200@60Hz".
Probably the resolution or the frequency are outside from monitor range. Or there is a bad/incompatible driver for my graphic card.
So I tried to test a new version of Knoppix (version 7.7.1), - Booting from USB, but there is a same problem.
I tested "CTRL"+"DEL"+"-" , but without responds.
Also, I tried F2 and starts the knoppix with several parameters many times (always with a same negative result).
Fox example, I tested these parameters:
knoppix screen=1280x1024
knoppix64 norandr
knoppix64 xmodule=nv screen=1280x1024
knoppix xserver=XFree86 xmodule=vesa
knoppix screen=1280x1024 vsync=60 xmodule=svga
knoppix screen=1280x1024 vsync=60 hsync=60
knoppix screen=1920x1200 vsync=60 hsync=60
I am using a desktop pc with this hardware:
Processor AMD FX-8300, MotherBoard ASUS M5A97 LE R2.0, 16 GB RAM
!! Graphic Card ASUS TURBO GTX1060 6GB
!! monitor DELL U2412M (maximal res. 1920x1200 @ 60 Hz)
I will happy for any suggestions, because this is frustrating for me (I haven't got my original Graphic card yet).
Or, maybe some update of driver package in new version of Knoppix could helps.
Thank you.
did you use CD attached to graphic card and new screen? First connect old screen and install graphics card and make sure its working fine. After this you screen should work fine as well so do this and tell me results.
I would like to echo this question. I'm having the same problem. Has anyone solved this problem or have a work around?
Juniper EX4300-24T Layer 3 24 Ports Manageable Ethernet Switch 1 Year Warranty
$139.00
Juniper EX2200-C-12T-2G 12 Port L3 EX2200-C Compact Fanless Switch 1YearWarranty
$154.00
Juniper Networks EX2300-24P 24 Port Gigabit PoE 4 SFP 1/10G Network Switch
$119.00
Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord
$54.99
Juniper EX4300-48T 48 Port 1G 4 QSFP 40G Dual PSU AFO w/ Rails, EX-UM-4X4SFP Mod
$169.00
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch
$50.95
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$315.00
Juniper EX4600-40F-AFO 24 SFP+/SFP Ports 4 QSFP+ Ports Switch - Dual AC PSU
$950.00
Juniper QFX5100-48S 48-Port 10GbE SFP+ 6x40GbE QSFP Network Switch w/Ears Tested
$599.99
Juniper Networks SRX240 16-Port Security Gateway Firewall Appliance SRX240H
$47.99