-
How do I fix "Kernel panic" error when booting USB stick?
Summary:
1. I want to create a bootable USB stick with a live Knoppix DVD iso on it,
without first having to put the iso file on a DVD and boot it. However, it's not
the latter proviso that is my problem.
NOTE:
To do the above, I originally followed klaus2008's instructions at
http://knoppix.net/forum/threads/317...le-usb-stick#3.
HOWEVER, he uses the syslinux bootloader, which uses FAT32. The problem is that
one of the files copied to the FAT32 stick is 4.3Gb (/KNOPPIX/KNOPPIX), and
FAT32 can't handle files greater than 4Gb (the copy fails).
SO I USED GRUB LEGACY INSTEAD OF SYSLINUX. But after WEEKS of effort and
research, I can't get past a "Kernel panic" error in the grub boot.
In case it's relevant, I'm using the iso KNOPPIX_V7.7.1DVD-2016-10-22-EN.iso,
whereas klaus2008's instructions are based on Knoppix 7.6.0.
2. The situation is as follows:
I have succeeded in putting the appropriate parts of the knoppix iso on a USB
stick (by following klaus2008's instructions), and in installing the grub
(legacy) bootloader (ver 0.97) on the stick.
I put the stick in the slot, switch on the laptop, and the grub on the stick
loads OK. But when I select the grub menu entry to launch the boot, I get the
following error:
"Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)"
and the boot goes no further.
The grub menu.lst entry is:
title KNOPPIX DVD on memory stick
root (hd0,0)
kernel /boot/isolinux/linux lang=en apm=power-off initrd=/boot/isolin
ux/minirt.gz nomce libata.force=noncq hpsa.hpsa_allow_any=1 loglevel=1
(The "kernel" entry is all on one line.)
The entry "root (hd0,0)" IS correct because when a stick is used to boot from,
my system designates it as "root (hd0,0)".
MY QUESTION:
Please could you tell me why I'm getting the "Kernel panic", and how do I make
the boot succeed?
Full details:
1. To create the bootable USB stick with the live Knoppix DVD iso on it, I
followed the instructions on the following site, as my MAIN BASE to work from
(post #3, klaus2008 ):
http://knoppix.net/forum/threads/317...le-usb-stick#3
2. Those instructions tell you to use the syslinux bootloader. But syslinux
works with a FAT filesystem, which only supports files up to 4Gb (using FAT32).
One of the files to be copied from the iso file on the hard drive to the
stick is 4.3Gb (namely /KNOPPIX/KNOPPIX). And sure enough the copy failed.
3. So I used the grub bootloader instead, and formatted the stick as ext3 (a
single partition). I assumed that grub supports ext3. The 4.3Gb file now copied
OK.
See "6." for how I put grub on the stick.
4. But when booting the stick, I got the "Kernel panic" error in the "Summary".
From googling the "Kernel panic" message, there appear to be two main
suggestions for correcting the problem: a) use another version of grub, or b)
boot a different kernel.
I've tried the latter, but still get the same error. To be honest, I'M OUT OF
MY DEPTH HERE, so your handholding guidance would be much appreciated.
5. I ought to mention that when I created /boot/grub/menu.lst on the stick, I
did the following.
I based menu.lst on what I believe is the equivalent entry in
/boot/isolinux/isolinux.cfg on the stick. That isolinux.cfg entry is
LABEL knoppix
KERNEL linux
APPEND lang=en apm=power-off initrd=minirt.gz nomce libata.force=noncq
hpsa.hpsa_allow_any=1 loglevel=1
(The "APPEND" entry is all on one line.)
So based on that, I created the following entry in menu.lst
title KNOPPIX DVD on memory stick
root (hd0,0)
kernel /boot/isolinux/linux lang=en apm=power-off initrd=/boot/isolin
ux/minirt.gz nomce libata.force=noncq hpsa.hpsa_allow_any=1 loglevel=1
(The "kernel" entry is all on one line.)
6. I put grub on the stick in the following way:
$ sudo grub-install --root-directory=/media/sdb1 /dev/sdb
Installation finished. No error reported.
This is the contents of the device map /media/sdb1/boot/grub/device.map.
Check if this is correct or not. If any of the lines is incorrect,
fix it and re-run the script `grub-install'.
(fd0) /dev/fd0
(hd0) /dev/disk/by-id/ata-TOSHIBA_MK1059GSMP_Z1Q7P2H2T
(hd1) /dev/disk/by-id/usb-SanDisk_Cruzer_Edge_20035000721D97C341C9-0:0
$
I understand that the above command puts the grub bootloader in the MBR of the
stick, and it put 10 files into /boot/grub/ on the stick.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
IBM QRadar xx29 Server 4412Q2A
$200.00
IBM Power S822 12-Bay Server System Power8 Core 3.42Ghz DVD-Rom Drive 64GB No HD
$399.99
IBM SYSTEM x3200 M2 Server - HDD wiped, No OS
$75.00
IBM Power 720 POWER7 00E6516 3.6GHz CPU 64GB RAM Server
$209.98
ibm server z series
$16000.00
IBM 7944AC1 System x3550 M3 Server 1*Intel Xeon X5650 2.67GHz 4GB SEE NOTES
$27.25
IBM Power S822 8284-22A 12SFF Power8 3.89GHz 6-Core 64GB RAM No Bezel/HDD Server
$319.99
IBM Lenovo X3650 M5 2U 8x 2.5” CTO Rack Server – 2x HS, 2x 750W
$199.00
IBM SYSTEM x3650 M4 Xeon E5-2609 2.40GHZ 16GB DDR3-1066MHZ 2x 550W PSU TESTED
$109.95
IBM System X3500 M4 7383AC1 (E5-2650 v2 2.60GHz - 192GB RAM - M2000 - NO OS/HDD)
$294.92