I failed to write that I have searched using:Output:Code:sudo whereis mlxprgconfigi.e., no existence.Code:mlxprgconfig:
My Desktop Knoppix has to configure the system for Samsung SyncMaster 1360X768. Used Nvidia for x86 version 304.125 to set my monitor way back. It remained set that way.
Recently, I thought that I should use my AMD's 64-bit operation rather than the Intel's 32bit. I downloaded the corresponding driver for x86-64. But doesn't get installed. Perhaps because Knoppix only addresses x86-64bit for intel processors. I had forgotten that it doesn't address the AMD processors.
But because of this fiddling with my system, another problem crept up. To use the monitor I have to reinstall the driver upon every boot. Knoppix overwrites the drivers as well, not only the xorg.conf, upon subsequent boots and falls back on partial screen default even with vga=792 cheatcode.
There is a line in /etc/X11/xorg.conf :It is also written that:# Created by KNOPPIX # Delete this line if you don't want KNOPPIX to overwrite your /etc/X11/xorg.conf
I have deleted the lines from xorg.conf but knoppix still overwrites the nvidia setup files. I had followed some other steps during the first set up, but did not write it down. So I can't use them now. I also searched the knoppix forum, but similar threads don't come to my notice.# Monitor section auto-generated by KNOPPIX mlxprgconfig
I have kept a back-up of my xorg.conf file as xorg.conf.rajiabando . When the full screen didn't activate during the subsequent boots, I have at init 3, used pico and copied the back-up as xorg.conf, but this simple task doesn't help. Knoppix is also overwriting some of the nvidia files.
Why didn't it do so earlier, because of which I continued to have my full screen displays across all the subsequent boots?
Why it isn't returning the full screens now?
These are the questions upon which I am tearing my hair. [Don't worry, I can't, because I regularly have my hair cropped with my shaver]
Generally, I have notes of all my systems settings with me. This omission appears to be one of those idiotic decisions I have taken without thinking properly.
Could I please be helped?
Last edited by rajibando; 03-09-2018 at 07:19 AM. Reason: clarity, typo
I failed to write that I have searched using:Output:Code:sudo whereis mlxprgconfigi.e., no existence.Code:mlxprgconfig:
Juniper QFX5100-48S-AFI 48x SFP+/SFP Ports 6x QSFP Ports Switch
$349.99
Juniper EX2200-C-12T-2G Gigabit Ethernet Managed Switch
$59.99
Juniper QFX5200-32C-AFO QFX5200 32 port 100 Gigabit QSFP28 Switch
$645.00
Juniper Networks EX-UM-4X4SFP EX4300 4 Port 1/10 Gigabit SFP+ Uplink Module
$39.00
Juniper EX2300-C-12P 12 Port PoE+ Rack Mountable Ethernet Switch
$249.99
Juniper EX3400-48P 48-Port PoE+ 4x SFP+ 2x QSFP+ Switch Factory Sealed
$295.00
Juniper SRX320 8-Port Security Services Gateway Appliance
$69.99
EX-SFP-1GE-T Juniper 740-013111 SFP 1000Base-T 10/100/1000 SFP NEW
$9.95
Juniper NFX250-S2 10-Port GbE & 2-Port SFP+ Layer 2 Network Services Platform
$209.99
Juniper Networks EX3300 SWITCH
$25.00