I failed to write that I have searched using:Output:Code:sudo whereis mlxprgconfigi.e., no existence.Code:mlxprgconfig:
My Desktop Knoppix has to configure the system for Samsung SyncMaster 1360X768. Used Nvidia for x86 version 304.125 to set my monitor way back. It remained set that way.
Recently, I thought that I should use my AMD's 64-bit operation rather than the Intel's 32bit. I downloaded the corresponding driver for x86-64. But doesn't get installed. Perhaps because Knoppix only addresses x86-64bit for intel processors. I had forgotten that it doesn't address the AMD processors.
But because of this fiddling with my system, another problem crept up. To use the monitor I have to reinstall the driver upon every boot. Knoppix overwrites the drivers as well, not only the xorg.conf, upon subsequent boots and falls back on partial screen default even with vga=792 cheatcode.
There is a line in /etc/X11/xorg.conf :It is also written that:# Created by KNOPPIX # Delete this line if you don't want KNOPPIX to overwrite your /etc/X11/xorg.conf
I have deleted the lines from xorg.conf but knoppix still overwrites the nvidia setup files. I had followed some other steps during the first set up, but did not write it down. So I can't use them now. I also searched the knoppix forum, but similar threads don't come to my notice.# Monitor section auto-generated by KNOPPIX mlxprgconfig
I have kept a back-up of my xorg.conf file as xorg.conf.rajiabando . When the full screen didn't activate during the subsequent boots, I have at init 3, used pico and copied the back-up as xorg.conf, but this simple task doesn't help. Knoppix is also overwriting some of the nvidia files.
Why didn't it do so earlier, because of which I continued to have my full screen displays across all the subsequent boots?
Why it isn't returning the full screens now?
These are the questions upon which I am tearing my hair. [Don't worry, I can't, because I regularly have my hair cropped with my shaver ]
Generally, I have notes of all my systems settings with me. This omission appears to be one of those idiotic decisions I have taken without thinking properly.
Could I please be helped?
Last edited by rajibando; 03-09-2018 at 07:19 AM. Reason: clarity, typo
I failed to write that I have searched using:Output:Code:sudo whereis mlxprgconfigi.e., no existence.Code:mlxprgconfig:
Cisco Catalyst C9300-24UX-A 24 Port 10G/mGig Copper UPOE Network Switch
$475.00
Fortinet FortiSwitch FS-124D-POE 24 Port Gigabit Ethernet Switch UNREGISTERED
$99.97
Loocam Gigabit PoE Switch 8 Port 96W 2 Uplink Port Unmanaged Ethernet Switch
$49.99
ARUBA J9772A 2530-48G PoE+ 48 PORT ETHERNET SWITCH W/ RACK EARS J9772-60301
$140.23
NETGEAR GS108 ProSafe 8-Port GbE Unmanaged Switch w/ Power Adapter
$14.99
NETGEAR GS305300PAS 5 Port Gigabit Ethernet Unmanaged Switch
$22.99
NETGEAR ProSafe GS724T Rack Mountable Managed Gigabit Switch
$20.00
TP-Link TL-SG108 8-Port 10/100/1000 Mbps Gigabit Ethernet Desktop Switch FREE SH
$14.99
Arista DCS-7050SX-64 48-Port SFP+ 4-QSFP Network Switch 2x PSU w/Ears Tested
$214.99
Netgear Prosafe 48-Port GbE & 4-Port SFP Managed Network Switch GS752TS
$59.99