MODEM
-----
Recently, I have installed knoppix (version 3.1-12-12-2002) on hdd. After that, I have downloaded a convenient driver for my "windmodem"(driver: pctel-0.96) and installed it on my computer. further information for the driver/modem:
http://pctelcompdb.sourceforge.net/
my modem: HSP56 world micromodem, chipset: pct789
http://pctelcompdb.sourceforge.net/v...s.php?id_no=47
In Mandrake 8.2 my modem is working without any problems; there I used the pctel-0.94 driver. But I wasn´t able to install the driver on my knoppix system successfully. (maybe some problems with the kernel?)
I hope,the following information might be helpful:
#lspci
------
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3189
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168
00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
00:09.0 Ethernet controller: BROADCOM Corporation: Unknown device 4401 (rev 01)
00:0b.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02)
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti4200] (rev a3)
#lspci-n
--------
00:00.0 Class 0600: 1106:3189
00:01.0 Class 0604: 1106:b168
00:07.0 Class 0c00: 1106:3044 (rev 46)
00:09.0 Class 0200: 14e4:4401 (rev 01)
00:0b.0 Class 0703: 134d:7892 (rev 02)
00:10.0 Class 0c03: 1106:3038 (rev 80)
00:10.1 Class 0c03: 1106:3038 (rev 80)
00:10.2 Class 0c03: 1106:3038 (rev 80)
00:10.3 Class 0c03: 1106:3104 (rev 82)
00:11.0 Class 0601: 1106:3177
00:11.1 Class 0101: 1106:0571 (rev 06)
00:11.5 Class 0401: 1106:3059 (rev 50)
01:00.0 Class 0300: 10de:0253 (rev a3)
I tried to connect to my provider with wvdial: (file created by wvdial.conf)
[Dialer Defaults]
Modem = /dev/modem
Baud = 115200
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Dial Command = ATDT
Modem Type = Analog Modem
Phone = 0191011
Username = 123456790
Password = *****
OUTPUT:
------------
-->Wvdial : Internet Dialer Version 1.53
PCTel Initialization. Country code = 0
-->Initializing modem
-->Sending: ATZ
ATZ
OK
-->Modem initialized.
-->Sending:ATDT0191011
-->Waiting for carrier.
ATDT0191011
Connect 48000
-->Carrier detected.Waiting for prompt.
-->Connected but carrier signal lost! Retrying...
-->Sending: ATDT0191011
-->Waiting for Carrier
NO CARRIER
After "NO CARRIER" the dialing process restarts, the modem tries to connect again some times, but without success?!
thx
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$13.50
Team T-FORCE VULCAN Z 32GB (2 x 16GB) PC RAM DDR4 3200 (PC4 25600) Memory
$50.99
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$16.50
HyperX FURY DDR4 4GB 8GB 16GB 32GB 3200 2400 2666 Desktop RAM Memory DIMM 288pin
$8.99
Kingston HyperX FURY DDR3 8GB 16GB 32G 1600 1866 1333 Desktop Memory RAM DIMM
$13.25
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
HyperX FURY RAM DDR4 16GB 8GB 32GB 4GB 3200 2666 2400 2133 Desktop Memory DIMM
$9.64
USB Flash Drive Memory Stick Pendrive Thumb Drive 4GB, 8GB, 32GB, 64GB 128GB LOT
$230.40
Lot Of 10 Mixed Samsung 16GB 2Rx4 PC4-2133P RDIMM DDR4-17000 ECC Server Memory
$134.99