MODEM
-----
Recently, I have installed knoppix (version 3.1-12-12-2002) on hdd. After that, I have downloaded a convenient driver for my "windmodem"(driver: pctel-0.96) and installed it on my computer. further information for the driver/modem:
http://pctelcompdb.sourceforge.net/
my modem: HSP56 world micromodem, chipset: pct789
http://pctelcompdb.sourceforge.net/v...s.php?id_no=47
In Mandrake 8.2 my modem is working without any problems; there I used the pctel-0.94 driver. But I wasn´t able to install the driver on my knoppix system successfully. (maybe some problems with the kernel?)
I hope,the following information might be helpful:
#lspci
------
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3189
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168
00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
00:09.0 Ethernet controller: BROADCOM Corporation: Unknown device 4401 (rev 01)
00:0b.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02)
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti4200] (rev a3)
#lspci-n
--------
00:00.0 Class 0600: 1106:3189
00:01.0 Class 0604: 1106:b168
00:07.0 Class 0c00: 1106:3044 (rev 46)
00:09.0 Class 0200: 14e4:4401 (rev 01)
00:0b.0 Class 0703: 134d:7892 (rev 02)
00:10.0 Class 0c03: 1106:3038 (rev 80)
00:10.1 Class 0c03: 1106:3038 (rev 80)
00:10.2 Class 0c03: 1106:3038 (rev 80)
00:10.3 Class 0c03: 1106:3104 (rev 82)
00:11.0 Class 0601: 1106:3177
00:11.1 Class 0101: 1106:0571 (rev 06)
00:11.5 Class 0401: 1106:3059 (rev 50)
01:00.0 Class 0300: 10de:0253 (rev a3)
I tried to connect to my provider with wvdial: (file created by wvdial.conf)
[Dialer Defaults]
Modem = /dev/modem
Baud = 115200
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Dial Command = ATDT
Modem Type = Analog Modem
Phone = 0191011
Username = 123456790
Password = *****
OUTPUT:
------------
-->Wvdial : Internet Dialer Version 1.53
PCTel Initialization. Country code = 0
-->Initializing modem
-->Sending: ATZ
ATZ
OK
-->Modem initialized.
-->Sending:ATDT0191011
-->Waiting for carrier.
ATDT0191011
Connect 48000
-->Carrier detected.Waiting for prompt.
-->Connected but carrier signal lost! Retrying...
-->Sending: ATDT0191011
-->Waiting for Carrier
NO CARRIER
After "NO CARRIER" the dialing process restarts, the modem tries to connect again some times, but without success?!
thx
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$95.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$12.99
New Cisco GLC-TE 1G SFP Copper RJ45 100m 1000BASE-T Transceiver Module
$21.62
🔥🔥🔥 CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi Module 🔥🔥🔥
$6.80
GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03
$6.80
Genuine Cisco ‎SFP-10G-SR Transceiver Module (10-2415-03)
$5.85
CISCO SFP-10G-LR SFP TRANSCEIVER MODULE GBIC 10G 10GB SFP - 1 Year Warranty
$39.99
LOT OF 10 HPE JD092B X130 10G SFP+ LC SR Transceiver
$40.00
Fully Compatibility 10GBase-T Transceiver SFP-10G-T SFP+ to RJ45 Copper 30M 80M
$58.50