-
USB 2.0 Support?
I've just downloaded knoppix build 2003-01-01
It booted fine and detected all my USB 2.0 peripherals (harddrive, CD-R/RW, hub, pcmcia host controller) but they've come up only at USB 1.1 speeds.
Does anyone know how I can make it run at the full USB 2.0 speed?
The harddrive is so slow at 12 Mbps!
Thanks
-
Senior Member
registered user
Re: USB 2.0 Support?
' modprobe ehci-hcd '
From /usr/src/linux-2.4.20-xfs/Documentation/usb/ehci.txt
[[
The EHCI driver is used to talk to high speed USB 2.0 devices using
USB 2.0-capable host controller hardware. The USB 2.0 standard is
compatible with the USB 1.1 standard. It defines three transfer speeds:
- "High Speed" 480 Mbit/sec (60 MByte/sec)
- "Full Speed" 12 Mbit/sec (1.5 MByte/sec)
- "Low Speed" 1.5 Mbit/sec
USB 1.1 only addressed full speed and low speed. High speed devices
can be used on USB 1.1 systems, but they slow down to USB 1.1 speeds.
USB 1.1 devices may also be used on USB 2.0 systems. When plugged
into an EHCI controller, they are given to a USB 1.1 "companion"
controller, which is a OHCI or UHCI controller as normally used with
such devices. When USB 1.1 devices plug into USB 2.0 hubs, they
interact with the EHCI controller through a "Transaction Translator"
(TT) in the hub, which turns low or full speed transactions into
high speed "split transactions" that don't waste transfer bandwidth.
At this writing, this driver has been seen to work with implementations
of EHCI from (in alphabetical order): Intel, NEC, Philips, and VIA.
]]
Originally Posted by
Tom
I've just downloaded knoppix build 2003-01-01
It booted fine and detected all my USB 2.0 peripherals (harddrive, CD-R/RW, hub, pcmcia host controller) but they've come up only at USB 1.1 speeds.
Does anyone know how I can make it run at the full USB 2.0 speed?
The harddrive is so slow at 12 Mbps!
Thanks
Similar Threads
-
By alexjenx in forum Hardware & Booting
Replies: 1
Last Post: 05-27-2004, 01:08 AM
-
By langhaarrocker in forum Customising & Remastering
Replies: 2
Last Post: 05-22-2004, 07:45 PM
-
By dork in forum General Support
Replies: 0
Last Post: 05-05-2004, 06:12 PM
-
By baldyeti in forum The Lounge
Replies: 3
Last Post: 11-28-2003, 11:18 PM
-
By ranch137 in forum General Support
Replies: 2
Last Post: 04-16-2003, 06:08 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
lot of 10 Juniper EX-SFP-10GE-SR Compatible 10GBASE-SR SFP+ 850nm 300m DOM -J499
$220.00
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord
$43.95
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$210.00
Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord
$54.99
EX2300-24P Juniper 24-port 10/100/1000BASE-T PoE+ 4 x 1/10GbE SFP/SFP+ UNCLAIMED
$450.00
Juniper Networks EX3400-48P 48x Gigabit PoE+ RJ45 2x 40Gb/s QSFP+ Switch
$166.24
Juniper Networks EX2200-C-12P-2G 12 Port Gigabit PoE 2 T/SFP 1G Network Switch
$129.00
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$41.28
Juniper Networks EX3300-24P 24-Port PoE+ 4x SFP+ Network Switch TESTED
$79.99
Juniper EX2300-48P PoE+ Switch 48x 1GbE & 4 SFP+/SFP 10G uplinks, Tested
$289.00