Check out the Cheat Codes for optional bootup switches.
http://knoppix.net/wiki/Cheat_Codes
I have a 64-bit processor on a Dell 9360 machine.
If I boot into Knoppix 8.2.0 Live from a portable drive and run simple queries as follows I get:
$ lscpu
Architecture: x86_64
CPU op-mode(s): 32 bit,64 bit
Flags: ... lm ...
$ lshw -C processor | grep width
width: 64 bits
$ grep flags /proc/cpuinfo | grep " lm "
Flags: ... lm ...
which all confirm the 64-bit architecture. BUT the response
CPU op-mode(s): 32 bit,64 bit
apparently indicates that I am running a 64-bit-capable machine in 32-bit-mode.
Yes? - is this a true interpretation?
My /boot/isolinux/isolinux.cfg file contains the lines (omitting redundant qualifiers for ease of reading)
DEFAULT fergus
LABEL fergus
KERNEL ifcpu64.c32
APPEND knoppix64 -- knoppix
APPEND knoppix64
LABEL knoppix
KERNEL linux
APPEND initrd=minirt.gz
LABEL knoppix64
KERNEL linux64
APPEND initrd=minirt.gz
which I hoped meant "if 64-bit machine use 64-bit OS; if 32-bit machine use 32-bit OS" but apparently not.
How can I tweak the isolinux.cfg file to behave as required one line up?
Thank you!
PS1 I have to admit (I have only just noticed) that the file ifcpu64.c32 referred to above is very suggestive of an instruction "if 64-bit machine use 32-bit OS". Is that what it achieves, and the cause of the mismatch described?
PS2 I use this ifcpu file from the Knoppix 7.4.2 provision. I find the Knoppix 8.2.0 version stops Knoppix stone dead before it even starts. It simply does not work, at all. Anybody else?
Check out the Cheat Codes for optional bootup switches.
http://knoppix.net/wiki/Cheat_Codes
lot of 10 Juniper EX-SFP-10GE-SR Compatible 10GBASE-SR SFP+ 850nm 300m DOM -J499
$220.00
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord
$43.95
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$210.00
Juniper EX3300-48P, 48 Port PoE+ Gigabit Network Switch w/ Power cord
$54.99
EX2300-24P Juniper 24-port 10/100/1000BASE-T PoE+ 4 x 1/10GbE SFP/SFP+ UNCLAIMED
$450.00
Juniper Networks EX2200-C-12P-2G 12 Port Gigabit PoE 2 T/SFP 1G Network Switch
$129.00
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$41.28
Juniper 24-Port Gigabit Ethernet PoE+ & 4-Port SFP Network Switch EX2200-24P-4G
$38.95
Juniper Networks EX3300-24P 24-Port PoE+ 4x SFP+ Network Switch TESTED
$79.99
Juniper EX2300-48P PoE+ Switch 48x 1GbE & 4 SFP+/SFP 10G uplinks, Tested
$289.00