sudo rm /dev/dvd
ln -s /dev/dvd /dev/scd0 (or /dev/scd1 if your dvd drive is a second cdrom).
HTH
I've just installed Knoppix to a new desktop and I get a message that /dev/dvd is not found when I try and use mplayer to watch DVDs but I can open and view individual .vob files.
Since I am able to use mplayer to look at invidual .vob files by navigating into /dev/cdrom, I believe that I should be able to get this to work. I did a ls -l /dev/cdrom to see where it was pointing with the idea of creating a symlink from /dev/dvd to that same location.
When I ran ls -l /dev/cdrom, I got the following reply.
/dev/cdrom -> /dev/scd0
I then tried this:
ln -sf /dev/scd0 /dev/dvd, but I get the same error message that /dev/dvd is not found.
I also tried ln -sf /dev/hdc /dev/dvd, but again I get the same error.
I then used ls -l /dev/dvd and I got this: /dev/dvd -> /KNOPPIX/dev/dvd
It looks like /dev/dvd is pointing to the location that would be appropriate when running Knoppix from the CD, but now that it is on the hard drive things need to be updated. This should be simple enough, but I'm not exactly sure how to do this. Any ideas?
Thanks.
sudo rm /dev/dvd
ln -s /dev/dvd /dev/scd0 (or /dev/scd1 if your dvd drive is a second cdrom).
HTH
This is strange.
If I run a "cdrecord -scanbus", I get the following info back:
0,0,0 0) 'TOSHIBA ' 'DVD-ROM SD-M1402' '1010' Removable CD-ROM
The dvd should be located at scd0. But when I do a ln -s /dev/hdc /dev/dvd, I get the same error as before.
Now if I rm -f /dev/dvd and do ln -s /dev/hdc /dev/dvd, then I no longer get the message that /dev/dvd is not found but "Can't open VMG info!"
I thought that this might be due to permissions so I made sure that premissions for /dev/dvd and /dev/hdc were set right. Still got the same error message.
Then I decided to rm -f /dev/dvd and do ln -s /cdrom /dev/dvd. This actually works, but only if I have /cdrom mounted. I'm used to dvds automounting. This isn't too bad, but I'm at a loss to explain why the other didn't work. I'll still take suggestions if you have any.
Since you're using scsi emulation you can no longer refer to drives as /dev/hda (well not in this case anyway) but rather /dev/scd0.
Right, but I made a link to /dev/scd0 and that doens't work either. I've got an idea of what may be wrong, but I can't check it out till later. I'll post back info when I've got more.Originally Posted by rickenbacherus
LSI 9207-8i 8-Port SAS Non-RAID 6GBPS PCIe Host Bus Adapter
$34.95
Oracle 7085209 LSI MegaRAID SAS 9361-8i 1GB Cache 12Gbps SAS/SATA PCIe RAID Card
$28.20
Cisco UCS LSI MegaRAID 9271CV-8I SAS2308 PCIe SAS Internal RAID Controller
$28.00
LSI 9223-8I 6GBPS PCIe SAS Internal RAID Controller
$22.75
Inspur LSI 9300-8i Raid Card 12Gbps HBA HDD Controller High Profile IT MODE
$15.98
LSI MegaRAID 9361-8i 12Gb PCIe 8-Port SAS/SATA RAID 1Gb w/BBU/CacheVault/License
$39.95
LSI MegaRAID 9361-8i 12Gbps PCIe 3 x8 SATA SAS 3 8 Port RAID + BBU & CacheVault
$39.00
ORICO Multi Bay RAID Hard Drive Enclosure USB 3.0/ Type-C For 2.5/3.5'' HDD SSDs
$82.49
ACASIS 2.5/3.5 inch 2 Bay SATA USB 3.0 Hard Drive Disk HDD SSD Enclosure 4 RAID
$58.99
Dell PERC H330 PCIe 3.0 x8 RAID Storage Controller 04Y5H1 High Profile
$17.99