-
cd drives do not work after doing hd install
Hi,
After doing a hd install, my two cdroms do not work. One is a Plexterwriter CD-burner, and the other is a Panasonic DVD drive. Both are ide. Both drives worked perfectly when I ran knoppix off of the cd. But once I install to my hard disk, they both stop working.
In the beginning of the boot process, there is a message that the two drives are scsi, and that ide-scsi emulation is being used. Then later, there are error messages that sc0 and sc1 cannot be mounted. It is hard to see the exact messages because it is flying down so quickly. I know it would help if I could get the exact messages, but I'm not sure how.
Thanks!
-
Senior Member
registered user
Re: cd drives do not work after doing hd install
Originally Posted by
IamPi
It is hard to see the exact messages because it is flying down so quickly. I know it would help if I could get the exact messages, but I'm not sure how.
Thanks!
Open a console window and dmesg | less to see the boot messages one screen at a time, you can move up and down in the window with the arrow keys. When you post the error messages could you also post your /etc/fstab file also.
-
Senior Member
registered user
cat /proc/scsi/scsi will tell you if they appear on the SCSI BUS or not. as will cdrecord -scanbus. If they're on the SCSI BUS then your problem lies not with SCSI emulation but your /etc/fstab (as mentioned above) and likely some symlinks. Let's see what this gives you:
ls -al /dev/cdrom
ls -al /dev/cdrom1
and so on for any device listed in /etc/fstab. These are 'symlinks' and if you have those links they should look something like so:
Code:
$ ls -al /dev/cdrom
lrwxrwxrwx 1 root root 9 Aug 22 19:29 /dev/cdrom -> /dev/scd0
scd0 is the device name "SCSI Drive 0". This naming convention makes it possible for applications to use the same name for a cdrom drive no matter where it is on your system. In other words you could effectively 'rename' and cdrom drive "/dev/cdrom". Rather than configure each application (cdplayer, cdburning app. etc) most Linux applications default to automatically try to use /dev/cdrom. Thus the need for symlinks. It also makes changing out a cdrom very easy. How? Just swap it- you already have the driver for it and it's in use so you needn't worry about finding/installing a new driver.
Similar Threads
-
By pbock in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 06-20-2005, 06:24 PM
-
By tabrown in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 04-11-2005, 12:46 PM
-
By oracle in forum Hardware & Booting
Replies: 1
Last Post: 09-05-2004, 06:44 AM
-
By rrfish72 in forum General Support
Replies: 15
Last Post: 08-05-2004, 07:33 AM
-
By gowator in forum Hdd Install / Debian / Apt
Replies: 0
Last Post: 01-22-2004, 11:35 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco Meraki MA-SFP-1GB-SX 1000BASE-SX SFP Transceiver Module
$24.99
Cisco GLC-FE-100FX-RGD 100BASE-FX SFP Transceiver Module
$17.99
Cisco GLC-FE-100LX-RGD 100BASE-LX SFP Transceiver Module
$17.99
Cisco SFP-10/25G-CSR-S 10/25GBASE-CSR SFP28, 850nm, 100m, LC,
$54.00
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
10Gtek ASF-10G-T 10GBase-T 10GbE SFP+ to RJ-45 Copper Optical Transceiver Module
$35.99
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00