I'd think that the Laserjets should work, at least. What version of Knoppix are you using? 3.2 works OK (although Cups has completely screwed up the papersize) on my Laserjet 3.
Could this be some networking issue?
I must be doing something fundamentally wrong when setting up printers with locahost after knx-hdinstall. Is there some trick to it that I should know about?
I cannot print from Kapps (KATE, KWrite, etc.). KATE, or whatever, just freezes after I try to print something right in the middle of the "generating printer data" dialog box every time.
Too bad you can't just use<K><KNOPPIX><CONFIGURE><CONFIGURE PRINTERS> as on the CD boot....or can you?
BTW, I don't think thisis the problem, but all my printers are HP (laserjet 5M, color laserjet 2500, deskjet 930C).
TIA,
I'd think that the Laserjets should work, at least. What version of Knoppix are you using? 3.2 works OK (although Cups has completely screwed up the papersize) on my Laserjet 3.
Could this be some networking issue?
Check in /etc/papersize for your proper settings it seems to default to a4 you probably want letter.Originally Posted by fingers99
Jorge: I answered in the other thread but i wiil repeat here you may want to wipe out cups entirely and start over and see if you get a better result. Although now that I am thinking I seem to remember in a thread about the new features of the knoppix-installer you have a knoppix and a debian install the knoppix variety is supposed to act like the cd running so you may want to look into that, just checked here's the thread.
It is A4, but that's what I want (hey, I'm a European: even in the UK letter has been obsolete for more than 20 years). What happens is that if the page is nearly "full" the printer posts a memory fault and doesn't print a full page. Obviously the memory is there, as it'll often print the rest on a new page.........Check in /etc/papersize for your proper settings it seems to default to a4 you probably want letter.
This is so wierd . Any ideas?
Remember the whales? Well its seems they're back and at it again....
Anyway, I seem to remember a thread about using the <KNOPPIX><Configure Printer> or an equivalent on a hdinstalled PC. Anyone remember this?
Also, I was going to try knoppix-installer but had to go with knx-hdinstall as I needed a boot disk and I never got that option in knoppix-installer. Now, if I use lilo in mbr with the KNOPPIX option on knoppix-installer how does my new server behave differently than the DEBIAN option? In other words, what are the pros and cons of not installing as DEBIAN? I guess I gain the <KNOPPIX><Configure Printer> and other KNOPPIX behaviors that I want. What do I loose?
TIA
I had similar to that using the driver in knoppix for my printer it would print the test or any other pages up to about 10-15 lines left and then the rest on the next page I went to http://www.linuxprinting.org and got the latest gimp-print.ppd file for my printer and followed the instructions for install and everything worked fine when I setup using that driver.Originally Posted by fingers99
I not sure of the exact differences but now that you have the boot floppy you could go ahead and do the knoppix-installer install you have your means to boot the system without lilo in the MBR the boot floppy from the old installer should still boot the new installer system it would use the same kernel and locations on the drive.Originally Posted by A. Jorge Garcia
Same symptoms as mine: I've snagged the ppd and bookmarked the instructions. Fingers crossed I'll get it working this weekend. Thanks Stephen.I had similar to that using the driver in knoppix for my printer it would print the test or any other pages up to about 10-15 lines left and then the rest on the next page I went to http://www.linuxprinting.org and got the latest gimp-print.ppd file for my printer and followed the instructions for install and everything worked fine when I setup using that driver.
OK, sounds like a plan. BTW, I can't use the WINXP boot loader as I'm not allowed to touch the BIOS or the WINXP partition....
Anyway, I'd like to get rid of all boot floppies if possible. Has anyone out there had a good experience with lilo in the mbr?
TIA,
1U Supermicro Server 10 Bay 2x Intel Xeon 3.3Ghz 8C 128GB RAM 480GB SSD 2x 10GBE
$297.00
HPE ProLiant MicroServer Gen8 Intel Xeon E3-1265L 16GB ECC PCIe x16 4x1TB HDD
$249.99
HP ProLiant Xeon E3-1220L V2 MicroServer Gen8 2.30 GHz 16 GB RAM NO DRIVES
$199.99
HP ProLiant Xeon E3-1220L V2 2.30 GHz 16 GB RAM MicroServer Gen8 NO DRIVES
$199.99
HPE ProLiant MicroServer Gen10 Plus v2 Ultra Micro Tower Server - 1 x Intel Xeon
$846.19
HP ProLiant HSTNS-5151 Micro Server 8GB RAM No Drives/Key/Caddies *READ*
$94.99
SuperMicro Server 505-2 Intel Atom 2.4GHz 8GB RAM SYS-5018A-FTN4 1U Rackmount
$202.49
Supermicro 5018A-FTN4 Rack Server - Black
$125.00
SUPERMICRO CSE-512 AMD Opteron Processor 6128, 32GB DDR3 RAM NO HDD
$90.00
1U 20" Short Depth Server Firewall PFSense X11SSH-F Xeon 3.5Ghz 32GB RAM NVME
$247.00