-
Need to modify post-install initrd (Fabian, can you help?)
After getting the appropriate modules (from Mandrake 9.2) for my Promise SATA150TX4, KNOPPIX now recognizes my Raptor hard drive. At the CD's boot prompt, I use:
knoppix modules-disk
After loading the three required module files from floppy, the Raptor is detected and I can access its partitions.
I've run the included installer scripts and everything seemed to complete without any problems. Unfortunately, I cannot boot the HD installation because the modules files needed to recognize the hard drive weren't added to the initrd.
How can I modify the post-install initrd to add the necessary module files? Per this thread, can someone like Fabian help?
**KEEP IN MIND, if I have to recreate the entire initrd, what modules are already included so I don't forget to keep them in the initrd?
Thanks in advance.
-SUO
Older related posts:
http://www.knoppix.net/forum/viewtopic.php?t=5487
http://www.knoppix.net/forum/viewtopic.php?t=5551
-
Senior Member
registered user
I'm looking to do something similar - install knoppix to a external 1394 HDD that I access via a 1394 PC Card.
When I last tried this (3.2 from about six months ago), I was able to install knoppix to the HDD OK, but then I wasn't able to mount the root on the 1394 drive. I played around with pcinitrd (the idea being to boot from CD/floppy, mount a temp root FS in the initrd, load pc card and all 1394 modules, mount the 1394 drive, then 'pivot' the root from the initrd to the 1394 drive), but did not succeed :( Unfortunately the pcinitrd howto/documentation does that it is an advanced technique and I'm just not experienced enough...
-
I'm hoping a simple command would take care of this "problem." I've just been too lazy/busy to e-mail Fabian directly, as I've noticed the PMs aren't working.
http://debian.tu-bs.de/knoppix/installer/
Maintainer: Fabian Franz <knoppix-installer - AT - fabian-franz - DOT -de>
Changed-By: Fabian Franz <knx-installer - AT - fabian-franz - DOT de>
-SUO
-
Just a bump. I have yet to get an e-mail response from Fabian (probably been at least a week now ).
-SUO
-
Senior Member
registered user
-
Thanks for the bump!
I've moved on to the 2.6 kernel which gives me all the support I need at the moment. Since the driver for my SATA controller is built into 2.6, I no longer need to mess with initrd. Unfrotunately, I've moved to Gentoo (where I can do an install directly with 2.6) until I can get a flavor of KNOPPIX that uses 2.6 from the very start.
-SUO
Similar Threads
-
By c123 in forum Hdd Install / Debian / Apt
Replies: 10
Last Post: 04-20-2004, 09:31 AM
-
By freeballer in forum Customising & Remastering
Replies: 0
Last Post: 10-13-2003, 11:26 PM
-
By bamarob in forum Hdd Install / Debian / Apt
Replies: 6
Last Post: 09-25-2003, 12:16 PM
-
By raid517 in forum Hdd Install / Debian / Apt
Replies: 36
Last Post: 08-31-2003, 06:24 PM
-
By andecla in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 04-18-2003, 07:53 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Intel Core i5-10500 3.10GHz Six-Core 12MB Cache Socket 1200 CPU Processor SRH3A
$89.99
Intel - Core i7-12700K Desktop Processor 12 (8P+4E) Cores up to 5.0 GHz Unloc...
$349.99
AMD Ryzen 5 5600X 6-core, 12-Thread Unlocked Desktop Processor
$99.95
Intel - Core i9-12900K Desktop Processor 16 (8P+8E) Cores up to 5.2 GHz Unloc...
$529.99
Intel Xeon SR3B6 GOLD 6148 20 CORE 2.40GHZ 27.5MB CPU
$80.00
Intel Core i7-7700 3.60GHz Desktop Computer CPU Processor SR338 Socket LGA1151
$64.95
Intel Core i5-12600KF Processor (4.9 GHz, 10 Cores, FCLGA1700) Box -...
$139.99
Intel - Core i5-12600K Desktop Processor 10 (6P+4E) Cores up to 4.9 GHz Unloc...
$289.99
INTEL CORE I5-11400 PROCESSOR | 2.60GHZ | SRKP0
$99.99
Intel Core i7-14700 2.1 GHz turbo 5.40 20-Core LGA1700 Processor 33MB 28 ++
$300.00