-
Senior Member
registered user
lilo.conf
When I boot from the CD I need the boot string:
knoppix vga=normal screen=1024x768 xvrefresh=60
how do I specify this boot sequence in lilo.conf?
I replaced the first line of lilo.conf with vga=normal instead of vga=791 and I added knoppix screen=1024x768 xvrefresh=60 to the beginning of the append string. This does not get me 1024x768 res however!
TIA,
-
Senior Member
registered user
Boot up with your cd and use the necessary "cheat-codes" to get X running as you want it, then mount your hd read/write and save the knoppix created /etc/X11/XFC86Config-4 file to your hd in etc/X11, then when you boot up your hd you will have the same XF86Config-4 file on your system as when you boot with the cd and proper cheat-codes.
Note: many of the knoppix cheatcodes are for knoppix hardware detection and setup and are not kernel parameters so you can't pass them to the kernel with lilo.
HTH
~rock
-
Senior Member
registered user
OK, Rock, that sounds doable.
BTW, so I should remove what I added to the append string, right? Also, should I leave vga=normal on the first line of lilo.conf?
EDIT: I'm having lots of problems with CUPS on my hdinstalled PCs using localhost:631. I have no problem configuring printers when running off the CD. Could something similar be done as you suggest above? IE: could I copy /etc/cups/cups.conf (or some other file?) that is configured correctly by the CD to my hdinstall?
Thanx!
-
Senior Member
registered user
OK, Rock, as usual, your advice is rock solid! I got my video on my hdinstall back to what it was with the CD boot.
All I had to do was mount hda7 and make it rw from the desktop. Then in a root shell I cp /etc/X11/XF86Config-4 /mnt/hda7/etc/X11/XF86Config-4 and reboot without the CD. Viola, ca c'est fini!
I'm teaching my students about java applets. Now I have an applet running on my home PC with width=600 and height=600 and I can see the whole thing in one Knoqueror window. My Dell at home has screen=1280x1024. At school, before I copied the KNOPPIX adjusted XF86Config-4 file, my students could not see much of the applet running by default 800x600 or less (I'm not sure). The Dells at school should default to 800x600 according to the manual, but it looks even smaller. At least now, at 1024x768, they see most of the applet. BTW: the applet in question is at http://calcpage.tripod.com/applets/drunk
Thanx!
-
Senior Member
registered user
Almost looks like you're playing Go, which I suppose makes sense, given your chess avatar.
JD
-
Senior Member
registered user
Well, actually, its a random walk in 2D (hence the name drunk).
BTW, anyone with experience with applets now if there's some way to see the drunk as he walks instead of the whole plot once the walk is done?
Regards.
-
Senior Member
registered user
leave the vga=normal line
and remove your changes to the append line
easy way to set up (configure) X, huh!
~rock
-
Senior Member
registered user
OK, good, that's what I did! Thanx.
BTW, what about configuring printers this way....
Regards,
-
Question
What kind secrets in the lilo.conf?
If we try to open etc/lilo.conf we can see there....bla-bla
go further to the end of lilo.conf
Label=Linux
something here
label=LinuxOLD
something here too
and in my lilo.conf...I have
Label=WinNT(hda1)
So, why on the lilo menu screen after reboot only:
Linux
WinNT(hda1)
Where LinuxOLD gone?
Now, try to rename label=Linux to Label=Knoppix or whatever you like...
run /sbin/lilo
and reboot
AND AGAIN lilo menu with
Linux
WintNT(hda1)
But where label Knoppix gone?
I am stuck with kernel compiling, I cant see another choices in Lilo menu
( I been trying add lines Linux-2.6-test), but the comp starts with choices:
Linux
WinNT(hda1)
What I need to do to see whole menu with choices?
-
Senior Member
registered user
Lilo will ignore anything that gives errors in the partition setup, that's why linux-Old is ignored.
Post your lilo.conf file and partition information so we can try to help.
~rock
Similar Threads
-
By tomjermy in forum Hardware & Booting
Replies: 1
Last Post: 03-17-2005, 01:07 AM
-
By totenengle in forum General Support
Replies: 2
Last Post: 07-09-2004, 03:39 AM
-
By *ix Newbie in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 12-20-2003, 05:06 PM
-
By greenbridge in forum Customising & Remastering
Replies: 0
Last Post: 08-11-2003, 08:51 PM
-
By mordor in forum General Support
Replies: 0
Last Post: 03-28-2003, 07:42 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
SUN Blade X6250 Server 8GB RAM DUAL PROCESSORS 594-4531-01
$109.99
Dell PowerEdge FX2 FX2S Enclosure - 4x PowerEdge FC640 w/ 8x Gold 6132 112C 1TB
$2699.99
Dell PowerEdge M620 0F9HJC Blade Server 2*E5-2670 2.60GHz 192GB RAM 2*300GB SAS
$103.99
Dell PowerEdge M630 Blade Server 1x Xeon E5-2630 v4 CPU / Motherboard P/N 0R10KG
$69.99
DELL M630 BLADE SERVER x2 XEON E5-2660V3 @ 2.6GH H730 PERC HDD CADDIES 16GB FC
$50.00
HP ProLiant BL460c G9 (Gen9) 2x E5-2670V3 12 Core 3.1GHz No Ram or No Drives
$59.98
HP ProLiant BL460c Server Blade (2 x CPU) 24GB RAM/No Drives
$45.60
LARGE Lot of HP ProLiant SL230s Gen8 Server Intel Xeon E5-2650 2.6Ghz 128GB
$28999.99
Dell PowerEdge M620 Blade Server
$39.99
Cisco UCS 5108 Blade Server Chassis Enclosure N20-C6508 4x PSU 8x Fans 2x Fabric
$139.99