-
Originally Posted by
Carlos_E_Morimoto
Try "fb 1024x768" (without "knoppix", just fb 1024x768 at boot line) this works with my two LCD monitors
In Italian market my 38B1 is Known or equivlent to 38B2 in other countries and a datasheet is viewable here:
http://www.fujitsu-siemens.com/rl/pe...8b2basic.html#
However :
Frequencies
Horizontal 30 - 60 kHz
Vertical 55 - 75 Hz
and 102x768 is supported with the refresh of 60 hz (48.36, 48.78 KHZ), 70 HZ (56.48 KHZ) ,72 HZ (57.52 KHZ), 75 HZ (60.02 KHZ and 60.24 KHZ)
Thanks for very tips to all
Rob
-
the entire situation
Using Matrox G400 16 MB and Fuitsu Siemens 38B1 at the startup I tried many tips of you( in combination too) and other tips of F2 screen
Then the message is the following
"You passed an undefined mode number. Press RETURN to see mode Vesa mode vailable.. I tried 0 (80x25 ) or 3 (80x2.
It is ok. The coloured text is good and so I can see many hardware well recognized and among these there is Matrox G400 16 MB AGP using XFree86 server - fbdev)
and a generic monitor voice
Tryng fb102x768 the screen is blinking, trying to start X11..
then I can read in text mode:
trying XFree (vesa)...failed
trying XFree (fbdev) ...failed
and then I return to command prompt
What do you think about this?
thanks
Rob
-
Does somebody have a clue, how to get knoppix running with a sony cpd-m151 tft lcd?
-
Senior Member
registered user
Undefined mode number
Hi I gete the same thing on bootup on my COMPAQ presario 1247 laptop. It says the same thing about passing an undefined mode number, and to wait or press space bar to continue, which i always do [press space bar] and it seems to work fine when KDE starts....I did dmesg and looked for any video related errors but found nothing....So I have no idea why it does that but it doesnt seem to be a problem.....i will look into this closer cause i would like it to start with no errors so i dont have to keep hitting the space bar every time! bob
-
hi all!
I have a similair problem with mine. i have a old Hewlitt Packard Pavilion monitor. and i also get the you have passed a undefined number to press return for video modes or press space bar to continue. everything seems to load ok and everythings detected. even my monitor but it detects it as a generic monitor. but anyway. it loads but when it gets to where your GUI is sposed to load, all i get is a flicker and then nothing but a black screen. I tried different video modes, tried the xmodule options. even tried telling it to run kde thinking it might be a compatability issue with one of the gui programs. but no such luck. my graphics card is a intel(r) 82810 graphics controller. when i had mandrake linux on my system i had no troubles running. don't have it now. i just have windows xp. I have 128 mb ram. hope this info helps. was hoping some one could help me. thankssss[/b]
-
Senior Member
registered user
If you have problem starting up X, check /etc/X11/XF86Config-4 and remove those modline entries and try again(startx at the command line), especially for LCD monitors.
-
umm i am a total noob to this lol i know to start it u just type x or xmodule at boot but have no idea how to do the rest. lol thanks
Sanny
Similar Threads
-
By dragonforce99 in forum Hardware & Booting
Replies: 3
Last Post: 07-08-2004, 11:45 PM
-
By nicorelli in forum General Support
Replies: 0
Last Post: 07-01-2004, 12:09 AM
-
By gyro in forum Hardware & Booting
Replies: 1
Last Post: 01-10-2004, 10:31 PM
-
By Simon_Haddad in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 10-27-2003, 06:23 AM
-
By ledatica in forum Laptops
Replies: 4
Last Post: 10-15-2003, 08:36 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$16.50
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$22.50
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$13.50
Pair Kingston HyperX FURY 16GB (2X8GB) PC3-14900 DDR3-1866Mhz Non-ECC Memory
$18.95
32GB ECC DDR3 RAM 2x16GB PC3L-12800R Desktop/Server Memory
$11.99
HyperX FURY RAM DDR4 16GB 8GB 32GB 4GB 3200 2666 2400 2133 Desktop Memory DIMM
$9.64
Lot of 50 DDR4 8GB PC4-2666V Laptop Memory RAM Mixed Major Brands
$474.99
A-Tech 128GB 8x 16GB 2Rx4 PC4-19200R DDR4 2400 ECC REG RDIMM Server Memory RAM
$175.92