Any clues how to get wlan-ng (prism2_cs) working in 3.3 11/19/03? I modified symlinked copies of /etc/modules.conf (to alias wlan0 prism2_cs), /etc/pcmcia/config.opts (to bind my card to prism2_cs), and /etc/pcmcia/wlan-ng.opts, so prism2_cs loads automatically. It creates wlan0, but cannot bring it up. I can assign an IP to wlan0, but its HWaddr ends up all zeros (wlan0 shows up in 'ifconfig -a', but not just plain 'ifconfig').
Everything looks good with the default orinoco_cs, except that does not support WEP on my SMC 2632W. So I am trying to get wlan-ng working, which works with WEP in SuSE 8.0 (using external pcmcia with i82365 instead of yenta_socket).
I cannot tell if the yenta_socket is the problem because if I start knoppix with nopcmcia and configure it to use i82365 instead, that fails and it uses yenta anyway. Or manually bringing up the modules in the same order as /etc/init.d/pcmcia fails when I try to modprobe or insmod i82365 (device not found).
root@tty2[knoppix]# cardmgr[1007]: socket 1: SMC 2632W 11mbps 801.11b WLAN Card
cardmgr[1007]: executing: 'modprobe prism2_cs'
cardmgr[1007]: + Note: /etc/modules.conf is more recent than /lib/modules/2.4.22
-xfs/modules.dep
init_module: prism2_cs.o: 0.2.0 Loaded
init_module: dev_info is: prism2_cs
cardmgr[1007]: executing: './wlan-ng start wlan0'
cardmgr[1007]: + /sbin/ifconfig wlan0 up
cardmgr[1007]: + SIOCSIFFLAGS: No such device
cardmgr[1007]: + /sbin/pump -i wlan0 > /dev/null
cardmgr[1007]: + Operation failed.
root@tty2[knoppix]# ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:300 (300.0 b) TX bytes:300 (300.0 b)
wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:3 Base address:0x100
root@tty2[knoppix]# iwconfig
lo no wireless extensions.
Warning: Driver for device wlan0 has been compiled with version 15
of Wireless Extension, while this program is using version 16.
Some things may be broken...
wlan0 IEEE 802.11-b Mode:Auto Access Point: 00:00:00:00:00:00
Encryption keyff
HGST Ultrastar HE10 HUH721010ALE600 10TB SATA 6Gb/s 7200RPM 3.5" Enterprise HDD
$69.99
Western Digital WD60PURZ 6TB Hard Drive SATA6 Gb/s 64MB Cache 3.5 Inch
$109.99
Western Digital RED NASware 3.0 WD40EFRX 4 TB SATA III 3.5 in NAS HARD DRIVE
$99.99
WF12F DELL 1TB 7.2K 6GBPS SATA 2.5'' HDD HARD DRIVE ST91000640NS 0WF12F
$25.00
HGST Ultrastar DC HC520 12TB SATA 6Gb 256MB 3.5" Enterprise HDD- HUH721212ALE601
$82.99
Seagate Exos 7E10 ST2000NM000B 2TB 7200RPM SATA 6.0Gb/s 3.5" Internal Hard Drive
$29.99
8TB Seagate Archive SATA 3.5" HDD Hard Drive 100% Healthy 200MB/s ST8000AS0002
$36.42
2 PACK Seagate ST1000LM035 Mobile HDD 1TB 2.5" SATA III Laptop Hard Drive
$26.85
WD 16TB Elements Desktop, Certified Refurbished Hard Drive - RWDBWLG0160HBK-NESN
$209.99
WD 4TB Certified Refurbished Elements, External Hard Drive - RWDBU6Y0040BBK-WESN
$84.99