Results 1 to 4 of 4

Thread: Mount USB 6-in-1 Multi-Flash card reader without recompile

  1. #1
    Junior Member registered user
    Join Date
    Aug 2003
    Posts
    24

    Mount USB 6-in-1 Multi-Flash card reader without recompile

    I recently purchased an Acomdata 6-in-1 USB Multi-Flash memory card reader for CompactFlash, SmartMedia/X-media. SD/MMC and Sony Memorystick cards (http://www.acomdata.com). I specifically chose Acomdata because they explicitly advertise that their product works with Linux as well as Windows and MacOS.

    The USB card reader is detected by Linux via the usb kernel modules (including the usb.c, usb-uhci.c, hub.c and usb-storage modules) as a multi-LUN SCSI device. Further, to access the SmartMedia filesystem, you also need the SDDR09 and SDDR55 usb-storage kernel modules (these provide the FAT emulation layer for Smartmedia). Finally, the manual for the Acomdata USB card reader recommends that you recompile the kernel to enable the SCSI Option "Probe all luns" (CONFIG_MULTI_LUN), which is normally disabled by default in the kernel because of potential problems.

    Fortunately, the Knoppix kernel is compiled with all of the necessary components, except for the SCSI multi-LUN option. You can still detect and mount the USB card reader devices without recompiling the kernel, however. Here's how you do it:

    1) Detect the USB mult-card reader devices. If you are booting from the Knoppix LiveCD, then at the boot prompt, pass the kernel option: knoppix max_scsi_luns=6.

    If you are booting from a hard-drive installation, then include the above kernel option under an "append" statement in /etc/lilo.conf e.g.: append="max_scsi_luns=6"; then as root, execute /sbin/lilo. When you reboot, dmesg will show the various devices in your USB multi-card reader detected as SCSI devices (e.g. sda, sdb, sdc, sdd).

    2) Mount your card media. On my system, sda is assigned to an Iomega Zip drive. Therefore, the various devices on the Acomdata USB multi-flash card reader are detected as:

    sdb: CompactFlash
    sdc: SmartMedia / X-media
    sdd: SD / MMC
    sde: Sony Memorystick

    I use only SmartMedia from my Olympus C-2000Z digital camera. To mount it, I execute (as root or superuser): mount -t vfat /dev/sdc1 /mnt/sdc1. Note that you need to specify the partition number when you mount ie. /dev/sdc1, not /dev/sdc. Of course, you can use mount points other than /mnt/sdc1.

    3) Diagnostics. If you are having trouble mounting your media card, execute dmesg | less to check if your USB card reader was detected. My dmesg shows:
    Code:
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    usb_control/bulk_msg: timeout
    scsi1 : SCSI emulation for USB Mass Storage devices
      Vendor: DMI       Model: MultiFlash        Rev: 3.00
      Type:   Direct-Access                      ANSI SCSI revision: 02
      Vendor: DMI       Model: MultiFlash        Rev: 3.00
      Type:   Direct-Access                      ANSI SCSI revision: 02
      Vendor: DMI       Model: MultiFlash        Rev: 3.00
      Type:   Direct-Access                      ANSI SCSI revision: 02
      Vendor: DMI       Model: MultiFlash        Rev: 3.00
      Type:   Direct-Access                      ANSI SCSI revision: 02
    Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi removable disk sdc at scsi1, channel 0, id 0, lun 1
    Attached scsi removable disk sdd at scsi1, channel 0, id 0, lun 2
    Attached scsi removable disk sde at scsi1, channel 0, id 0, lun 3
    You will also see some READ CAPACITY FAILED messages, which you can ignore.

    Alternatively, you can peruse the contents of /proc/scsi directory. If your USB multi-card reader is successfully detected, the file /proc/scsi/usb-storage-0/1 will be created. This file is plain text; if you execute 'less /proc/scsi/usb-storage-0/1', you should see something like this:
    Code:
       Host scsi1: usb-storage
           Vendor:                         
          Product: MultiFlash
    Serial Number: None
         Protocol: Transparent SCSI
        Transport: Bulk
             GUID: 0c0b27cb0000000000000000
         Attached: Yes
    If your USB multi-card reader is not detected, then the usb-storage-0 subdirectory will not appear under /proc/scsi.

  2. #2
    Junior Member
    Join Date
    Jan 2004
    Posts
    2
    Thanks spurious,

    Adding multi-LUN support did the trick.

    For those who don't want to use root account for such a trivial task as mounting removable media it might be helpful toadd following (or similar) lines in /etc/fstab.

    Code:
    /dev/sdc1               /mnt/SM                 auto    noauto,owner,user  0 0
    /dev/sdb1               /mnt/MMC                auto    noauto,owner,user  0 0
    I'm using SanDisk 6in1 reader with SmartMedia and SD/MMC cards only. For different types of readers the order of card slots might differ but testing with all drive letters helps.

    Naturally this works only if you are using only one portable media or always insert devices in the same order.

  3. #3
    Junior Member
    Join Date
    Jan 2004
    Posts
    2
    I forgot to mention the advantages of this approach

    After adding those lines you can mount media as normal user with command:
    mount /mnt/MMC

  4. #4
    Junior Member registered user
    Join Date
    Aug 2003
    Posts
    24
    I finished responding to a thread at linuxquestions.org regarding a Slackware user who was unable to mount a 6-in-1 USB card reader. Unfortunately, my final advice was to either recompile the Slackware kernel to enable CONFIG_MULTI_LUN or to install Knoppix.

    In the course of googling for my post, I found a good explanation of why the CONFIG_MULTI_LUN option is disabled by default: "the LUN stuff is a hack at best." For single-slot CompactFlash devices, the LUN code will detect additional phantom devices.

Similar Threads

  1. USB Card reader
    By lotech in forum General Support
    Replies: 0
    Last Post: 05-23-2005, 03:27 AM
  2. Multi card reader
    By richb in forum Hardware & Booting
    Replies: 1
    Last Post: 10-18-2004, 11:44 PM
  3. Compact Flash different sizes in USB reader - wiil not mount
    By stukennedyuk in forum Hardware & Booting
    Replies: 2
    Last Post: 02-14-2004, 03:41 PM
  4. Lexar media USB multi-card reader
    By VeeDubb in forum Hardware & Booting
    Replies: 12
    Last Post: 12-27-2003, 07:18 PM
  5. Toshiba SD Card Reader problem
    By josephy in forum Laptops
    Replies: 0
    Last Post: 11-10-2003, 03:54 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •