Sure you just need to boot into Linux and edit /etc/lilo.conf. Just set linux to default and comment out the 'prompt' entry. Then of course you must rerun lilo as root.
I followed these instructions:
http://www.knoppix.net/forum/viewtop...er=asc&start=0
And everything seems to work, it's just that there is some strange issue. When the computer boots, the windows boot menu thing pops up and lets me choose between windows or knoppix. When I choose knoppix, another menu pops up (this time from LILO I guess?) asking me whether I want to boot windows or knoppix! Is there a way to make it stop?
Thanks!
Sure you just need to boot into Linux and edit /etc/lilo.conf. Just set linux to default and comment out the 'prompt' entry. Then of course you must rerun lilo as root.
Thanks, I tried that and nothing. It seems like nothing I do to /etc/lilo.conf makes any difference! Here is my edited version, but I'm still getting the graphical menu and the prompt for Knoppix/Windows (and a 15 second delay even though I set it to 1). I also made sure to run lilo as root after the change, but still no luck
Code:vga=791 # /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)', # --------------- `install-mbr(8)', `/usr/share/doc/lilo/', # and `/usr/share/doc/mbr/'. # +---------------------------------------------------------------+ # | !! Reminder !! | # | | # | Don't forget to run `lilo' after you make changes to this | # | conffile, `/boot/bootmess.txt', or install a new kernel. The | # | computer will most likely fail to boot if a kernel-image | # | post-install script or you don't remember to run `lilo'. | # | | # +---------------------------------------------------------------+ # Support LBA for large hard disks. # lba32 # Overrides the default mapping between harddisk names and the BIOS' # harddisk order. Use with caution. #disk=/dev/hde # bios=0x81 #disk=/dev/sda # bios=0x80 # Specifies the boot device. This is where Lilo installs its boot # block. It can be either a partition, or the raw device, in which # case it installs in the MBR, and will overwrite the current MBR. # boot=/dev/hdb1 # Specifies the device that should be mounted as root. (`/') # root=/dev/hdb1 # Enable map compaction: # Tries to merge read requests for adjacent sectors into a single # read request. This drastically reduces load time and keeps the # map smaller. Using `compact' is especially recommended when # booting from a floppy disk. It is disabled here by default # because it doesn't always work. # # compact # Installs the specified file as the new boot sector # You have the choice between: bmp, compat, menu and text # Look in /boot/ and in lilo.conf(5) manpage for details # install=/boot/boot-menu.b #install=text # Specifies the location of the map file # map=/boot/map # You can set a password here, and uncomment the `restricted' lines # in the image definitions below to make it so that a password must # be typed to boot anything but a default configuration. If a # command line is given, other than one specified by an `append' # statement in `lilo.conf', the password will be required, but a # standard default boot will not require one. # # This will, for instance, prevent anyone with access to the # console from booting with something like `Linux init=/bin/sh', # and thus becoming `root' without proper authorization. # # Note that if you really need this type of security, you will # likely also want to use `install-mbr' to reconfigure the MBR # program, as well as set up your BIOS to disallow booting from # removable disk or CD-ROM, then put a password on getting into the # BIOS configuration as well. Please RTFM `install-mbr(8)'. # # password=tatercounter2000 # Specifies the number of deciseconds (0.1 seconds) LILO should # wait before booting the first image. # delay=1 # You can put a customized boot message up if you like. If you use # `prompt', and this computer may need to reboot unattended, you # must specify a `timeout', or it will sit there forever waiting # for a keypress. `single-key' goes with the `alias' lines in the # `image' configurations below. eg: You can press `1' to boot # `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'. # # message=/boot/bootmess.txt #prompt #timeout=150 # prompt # single-key # delay=100 # timeout=100 # Kernel command line options that apply to all installed images go # here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in # the Linux kernel `Documentation' directory. # # append="" append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce" # Boot up Linux by default. # default=Linux image=/boot/vmlinuz-2.4.22-xfs label=Linux initrd=/boot/initrd.gz read-only # restricted # alias=1 image=/vmlinuz.old label=LinuxOLD read-only optional # restricted # alias=2 # If you have another OS on this machine to boot, you can uncomment the # following lines, changing the device name on the `other' line to # where your other OS' partition is. # # other=/dev/hda4 # label=HURD # restricted # alias=3 #other=/dev/hda1 # label="Windows(hda1)"
The lilo.conf looks fine to me. The problem, I think, is that the bootsect.knx file you built when you followed the linked instructions is a copy of the old configuration -- from before you edited lilo.conf.
What you need to do is be root and run lilo (which you probably already did), and then go back to the instructions and repeat the steps where you build a bootsect.knx file and move it to Windows's root partition.
Worked like a charm, thanks a lot, I really appreciate your help!
Juniper EX2300-C-12P, 12 Port FANLESS POE Ethernet Switch EX2300-C
$375.00
Juniper Networks EX2300-C-12T Compact 12-Port EX2300-C Series Ethernet Switch
$300.00
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$59.95
Juniper Networks EX3300-24P | 24 Port Gigabit Network Switch w/ Power cord
$53.99
Juniper QFX5100-48T 48-Port 10G SFP 6-Port 40G QSFP Ethernet Switch Tested
$312.69
Juniper Networks EX3300 48-Port Gigabit Switch 4x SFP+ EX3300-48T SKU 10581
$69.99
Juniper Networks SRX320-POE 6-Port Service Gateway Security Appliance Tested
$149.99
Juniper Networks EX3300-48T 48 Port Gigabit 4x 10 GbE SPF+ Ports Switch - Tested
$40.00
Juniper Networks EX4400-48MP 48 port 5GbE + 12 port 10 Gigabit PoE++ Switch -NEW
$1200.00
Juniper Networks SRX220 8-Port Gigabit Services Gateway Security Appliance
$45.00