-
Grub/lilo boot problems
I made a new computer (yay), and proceeded install the Fedora Core. After playing with it for a little while, I thought "No, I don't think so", and did a hard disk install of my trusted knoppix CD (which served me so well in the past).
Everything was fine until reboot time, when it booted into grub, and stayed there. No kernel or os booted, I just got this grub prompt.
It goes into knoppix when I use the boot floppy, but not when it boots from hd. I'm assuming this is because Fedora wrote a boot sector that wasn't deleted by the knoppix install.
I tried looking into fdisk and cfdisk to see if I could wipe the hd and start again, but all the talk of cylinders and partitions confused me. If you write a partition, does it delete all data on the hd?
I also tried uninstalling grub using dselect. I assume that the grub that I uninstalled was a debian grub, not the one that is booting my system.
Is there an easy way to make the hd blank, as new, so that I can install knoppix again? Or a way to make lilo boot instead of this grub thing?
-
Senior Member
registered user
Did you let the knoppix installer proceed with lilo? If so, it might be installed, but another boot partition may be left active from fedora. Check with (c)fdisk that the partition onto which you installed knoppix is (the only one) marked active. If that does not suffice, post the result of "fdisk -l", and possibly your /etc/lilo.conf file. Alternatively, you could also edit the menu.lst file from your apparently working grub copy, and add your knoppix kernel there...
-
I did see a boot partition for fedora on cfdisk, but I deleted all partitions and rewrote two partitions, one for the swap and one for the main.
Should I have written the deletion before I wrote the new partition system? I thought writing a new partition system would do that anyway.
I set the main partition (not the swap) to be the boot partition, so I don't see where the problem is.
Similar Threads
-
By nhoxanh in forum General Support
Replies: 1
Last Post: 01-13-2005, 10:43 AM
-
By ocean in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 10-01-2004, 01:26 PM
-
By phantomshado in forum General Support
Replies: 1
Last Post: 02-14-2004, 06:45 AM
-
By keava in forum General Support
Replies: 3
Last Post: 10-20-2003, 05:24 PM
-
By jamesgf in forum Hdd Install / Debian / Apt
Replies: 6
Last Post: 03-27-2003, 05:16 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Juniper Networks EX2300-C-12T Compact 12-Port EX2300-C Series Ethernet Switch
$300.00
Juniper Networks MX80-AC Router 4 Port XFP 10G MIC-3D-200E-SFP
$600.00
Juniper Networks EX2200-C-12P-2G Gigabit Ethernet Managed Switch
$79.99
Juniper Networks EX3300 EX3300-48P 48-Port Gigabit PoE+ Switch
$59.95
Juniper Networks EX3300-24P | 24 Port Gigabit Network Switch w/ Power cord
$53.99
Juniper EX3400-48P 48-Ports PoE+ 4x SFP+ and 2x QSFP+ Managed Switch Tested
$135.00
Juniper EX2200-C-12T-2G 12-Port 10/100/1000 2x SFP Uplinks Compact Switch
$74.99
Juniper EX3400-48P 48 Port Switch PoE+ 4x SFP+ 2x QSFP 1xAC *Tested/Warranty*
$139.95
Juniper Networks EX4400-48MP 48 port 5GbE + 12 port 10 Gigabit PoE++ Switch -NEW
$1400.00
Juniper Networks EX2300-48P 48 Port Gigabit PoE 4 SFP 1/10G Network Switch
$185.00