-
Grub/lilo boot problems
I made a new computer (yay), and proceeded install the Fedora Core. After playing with it for a little while, I thought "No, I don't think so", and did a hard disk install of my trusted knoppix CD (which served me so well in the past).
Everything was fine until reboot time, when it booted into grub, and stayed there. No kernel or os booted, I just got this grub prompt.
It goes into knoppix when I use the boot floppy, but not when it boots from hd. I'm assuming this is because Fedora wrote a boot sector that wasn't deleted by the knoppix install.
I tried looking into fdisk and cfdisk to see if I could wipe the hd and start again, but all the talk of cylinders and partitions confused me. If you write a partition, does it delete all data on the hd?
I also tried uninstalling grub using dselect. I assume that the grub that I uninstalled was a debian grub, not the one that is booting my system.
Is there an easy way to make the hd blank, as new, so that I can install knoppix again? Or a way to make lilo boot instead of this grub thing?
-
Senior Member
registered user
Did you let the knoppix installer proceed with lilo? If so, it might be installed, but another boot partition may be left active from fedora. Check with (c)fdisk that the partition onto which you installed knoppix is (the only one) marked active. If that does not suffice, post the result of "fdisk -l", and possibly your /etc/lilo.conf file. Alternatively, you could also edit the menu.lst file from your apparently working grub copy, and add your knoppix kernel there...
-
I did see a boot partition for fedora on cfdisk, but I deleted all partitions and rewrote two partitions, one for the swap and one for the main.
Should I have written the deletion before I wrote the new partition system? I thought writing a new partition system would do that anyway.
I set the main partition (not the swap) to be the boot partition, so I don't see where the problem is.
Similar Threads
-
By nhoxanh in forum General Support
Replies: 1
Last Post: 01-13-2005, 10:43 AM
-
By ocean in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 10-01-2004, 01:26 PM
-
By phantomshado in forum General Support
Replies: 1
Last Post: 02-14-2004, 06:45 AM
-
By keava in forum General Support
Replies: 3
Last Post: 10-20-2003, 05:24 PM
-
By jamesgf in forum Hdd Install / Debian / Apt
Replies: 6
Last Post: 03-27-2003, 05:16 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Mellanox 10/25GbE SFP28 Network Card MCX512A-ACAT ConnectX-5 EN Ethernet Adapter
$284.00
1783-SFP1GTE Allen Bradley 1G copper SFP #ZYPL
$879.87
Cisco 110 24 Port 10/100 Ethernet Switch with 2 x SFP SF112-24-NA
$90.00
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
F5 Networks 10GB OPT-0016-00 F5-UPG-SFP+-R 10GBASE/SR SFP Transceiver
$4.00
Mellanox Original MFM1T02A-SR 10GbE 10GBASE-SR SFP+ Transceiver
$9.00
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00