-
Grub/lilo boot problems
I made a new computer (yay), and proceeded install the Fedora Core. After playing with it for a little while, I thought "No, I don't think so", and did a hard disk install of my trusted knoppix CD (which served me so well in the past).
Everything was fine until reboot time, when it booted into grub, and stayed there. No kernel or os booted, I just got this grub prompt.
It goes into knoppix when I use the boot floppy, but not when it boots from hd. I'm assuming this is because Fedora wrote a boot sector that wasn't deleted by the knoppix install.
I tried looking into fdisk and cfdisk to see if I could wipe the hd and start again, but all the talk of cylinders and partitions confused me. If you write a partition, does it delete all data on the hd?
I also tried uninstalling grub using dselect. I assume that the grub that I uninstalled was a debian grub, not the one that is booting my system.
Is there an easy way to make the hd blank, as new, so that I can install knoppix again? Or a way to make lilo boot instead of this grub thing?
-
Senior Member
registered user
Did you let the knoppix installer proceed with lilo? If so, it might be installed, but another boot partition may be left active from fedora. Check with (c)fdisk that the partition onto which you installed knoppix is (the only one) marked active. If that does not suffice, post the result of "fdisk -l", and possibly your /etc/lilo.conf file. Alternatively, you could also edit the menu.lst file from your apparently working grub copy, and add your knoppix kernel there...
-
I did see a boot partition for fedora on cfdisk, but I deleted all partitions and rewrote two partitions, one for the swap and one for the main.
Should I have written the deletion before I wrote the new partition system? I thought writing a new partition system would do that anyway.
I set the main partition (not the swap) to be the boot partition, so I don't see where the problem is.
Similar Threads
-
By nhoxanh in forum General Support
Replies: 1
Last Post: 01-13-2005, 10:43 AM
-
By ocean in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 10-01-2004, 01:26 PM
-
By phantomshado in forum General Support
Replies: 1
Last Post: 02-14-2004, 06:45 AM
-
By keava in forum General Support
Replies: 3
Last Post: 10-20-2003, 05:24 PM
-
By jamesgf in forum Hdd Install / Debian / Apt
Replies: 6
Last Post: 03-27-2003, 05:16 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco IE-3000-8TC Industrial Ethernet 8 Ports Managed Switch 1 Year Warranty
$114.00
Cisco Nexus 48-Port 10G SFP+ Switch N9K-9396PX w/ 9K-M12PQ 12-Port 40G QSFP
$249.99
Cisco WS-C4948-10GE-S Catalyst 4900 Series Layer4 Managed Switch 1 Year Warranty
$115.00
Juniper EX4300-24T Layer 3 24 Ports Manageable Ethernet Switch 1 Year Warranty
$195.00
HP 2530-48G 48 Port Gigabit Ethernet Network Switch J9775A
$30.95
New Linksys SE3005 5-port Gigabit Ethernet Switch
$18.99
New 10/100 Mbps 8 Ports Fast Ethernet LAN Desktop RJ45 Network Switch Hub
$11.49
Linksys SE3008 8 Ports Rack Mountable Gigabit Ethernet Switch
$21.99
HP ProCurve 2530-24G J9776A 24 Port Gigabit Ethernet Managed Network Switch
$34.99
Juniper Networks EX3300-48P 48-Port PoE+ 4x SFP+ Network Switch w/ Power Cord
$43.95