I have a netgear WA311 (or something its 802.11b) and at home.
However, I just used driverloader on a 802.11G card and it works well if you wanna stump up the cash!!!
It might be a better investment than a second b card!!!
Hi, I'm looking for a Wireless (802.11b) Card that works with Knoppix (PCI or USB). Can anyone who has gotten their card to work with knoppix please submit the full name to this posting (I'm stuck with Windoze until I can find one that works, I have a Linksys 802.11b WUSB11 v2.6 that doesn't work). Please also submit what version of Knoppix you are running. I want to install Knoppix to HD.
I have a netgear WA311 (or something its 802.11b) and at home.
However, I just used driverloader on a 802.11G card and it works well if you wanna stump up the cash!!!
It might be a better investment than a second b card!!!
The Orinoco / Proxim / etc work (orinoco, orinoco_cs, hermes) all work fine
The Linksys WPC 11 Version 1 - 3 work fine as well.
- Ambrose
I got an SMC 2345 PCMCIA card running using House of Craig's precomplied driver.
The driver was developed for the TI ACX100 chipset and can be studied at Source forge
Google either and you'll be there. There's a list of cards that'll work with this driver as well
Craig's instruction are flawless and I was up and runinng in a few minutes and am still running from the Live CD
I've had enough troubles just trying to get 802.11b to work with Windows, I think I'll 802.11b before sheeling for a new wireless router to go with the connector card. Thanks for the tip.Originally Posted by gowator
All right, I took a risk and got a D-Link DWL-520 card, it's Orinoco based and is recognized (but doesn't work so far) by Knoppix. I ran dmesg and I saw near the end.
orinoco-pci:Busy Timeout
I'm guessing there's a setting I need to change in the BIOS, does anyone know which one? Does anyone else have an Orinoco card that has had this problem?
I have a netgear 511 802.11g pcmcia card that works great when running the live cd. When I install knoppix to the hard drive, it stops working. Any ideas?
Hi.
I have a D-Link DWL-510 PCI board. It is a "11b" adaptor, works on windows, not linux. I don't even know what "chip" it has.
I will probably buy a new adaptor (PCI or USB) that works with knoppix directly, no driverloader or ndiswrapper. Any ideas? (I will look at the sugestion above)
/Ola A
I just got an SMC 2835W 802.11G card. It's supported by the prism54.org drivers which went into Knoppix 2004-02-09. I downloaded the 2004-02-16 release of Knoppix, burnt, ran the wavelan config (putting in the 128bit WEP key and the SSID) and voila I had eth0! Ran the network config and then I had my IP address back from the DHCP server! Very painless so here I am looking for the most apt place to post about it on knoppix.net and hopefully this will do! If your looking for painless 802.11G card for Knoppix I can heartedly recommend this one!
Edimax makes a good card and it's cheap, (PCI version for less than $25 bucks) Plus edimax distributes linux drivers on their site.
Dell Poweredge R640 Server | 2x Silver 4114 20 Cores | 96GB | 8x 1.8TB Dell SAS
$2749.99
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 1x 300GB HDD
$89.99
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell PowerEdge R730, 2 sinks, SystemBoard, 8 trays,H330,Idrac 8 exp, 2x750w Psu
$135.00
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x600Gb SAS, Proxmox
$360.00
DELL POWEREDGE T430 SERVER W/ DUAL XEON E5-2609 CPU & 16GB MEMORY
$329.00
Dell PowerEdge T330 E3-1240v5 3.5GHz 3.5" 8-Bay 8GB PERC H330 Server Tower
$200.00
DELL PowerEdge R630 8SFF Server 2x E5-2680v3 2.5GHz =24 Cores 32GB H730 4xRJ45
$240.00
Dell Poweredge R730xd 2.5in 2x E5-2690 v3 2.6ghz 24-Cores 64gb H730 2x 750w
$189.99