I've booted Knoppix on a machine with a blank HD, it does work. Not sure if I've tried it with that particular version but at least with 3.3-2003-11-19.
I was trying to install KNOPPIX on a completely new computer by booting off the CD. The harddisks were not formatted or partitioned. I was hoping to boot into KNOPPIX and use fdisk to partition the hd. However KNOPPIX (3.3-2003-09-24) seems to stop when detecting the hds and trying to create the fstab entry.
What I did was to boot from a dos diskette and partition the hds. After that everything was ok.
Does that mean that KNOPPIX can only run if the hds are partitioned? Or is this because I must wait longer? Or is it because I am not using the lastest KNOPPIX?
I was hoping to do everything from one CD.
I've booted Knoppix on a machine with a blank HD, it does work. Not sure if I've tried it with that particular version but at least with 3.3-2003-11-19.
Windos_No_Thanks,
Stupid question here, but, how do you get the DATE version, that both of you are speaking of???
True, someone else d/l'ed my v3.3, and burned the ISO image for me, is that where you get the date version you both are using? (from the ISO file itself?) Or can you get this date version from a command in Knoppix?
All I knew about was the uname part, i.e. I have:
Knoppix v3.3 v2.4.22-xfs
Thanks for any enlightenment,
Cuddles
IIRC the text on the boot screen tells you exactly which version it is when booting from CD, I'm not sure if/where it can be found on a HD install though.Originally Posted by Cuddles
Hmmmmm, oh well...
To add (quality) to the thread...
I installed Knoppix 3.3 - the one I mentioned above (previous), from just the CD - completely new hard drive - not even a partition table on the drive - who knows why it didn't work for you though.
This was on my new system, only one hard drive, and no previous OS was on it.
Cuddles
Could it be that I am not patient enough to wait for the detection process to finish? I waited for about 3 mins.
Or is it because its a SATA harddisk?
Hmmmmmm,
Just for my knowledge, what is a SATA hard disk?
I am familiar with IDE, and SCSI, I know "of" Flash, and USB, but I have never heard of this one. I have been out of the "main-stream" computer technology for about two years, being in a small town now, things are less visible here...
Thanks for the enlightenment,
Cuddles
I think he is refering to Serial ATA. More information is available at http://www.serialata.org/. Which probably explains why markleong is having difficulties.
Are you saying that KNOPPIX will have problems with SATA harddisks? Or it only my version of KNOPPIX?
I do not know if Knoppix works with SATA harddrives, perhaps someone else knows.
Cisco Systems NCS2K-20-SMRFS-L optical multiplexor CISCO EXCESS
$3599.00
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Cisco RV160 VPN Router 4 Gigabit Ethernet Ports RV160-K9-AR
$80.00
Cisco ASA5525-FTD-K9 Security Appliance with FirePower Services
$1000.00
Cisco WS-C3850-48P-L 48-Port Gigabit 3850 PoE Switch w/ 715W+ C3850-NM-4-1G Mod
$83.00
Cisco Catalyst WS-C2960-48TT-L V02 48 Port Fast Ethernet Switch
$34.00
Cisco C3850-NM-2-10G 2 Port Network Exp.Module for 3850
$38.99
Cisco WS-C4948-10GE-S 4948-10GE 48 Port Gigabit +10GB Switch w single AC 15.0 OS
$99.99
Cisco C9300-48 48 Port Switch Dual PSU W/C9300-NM-8X P/N: C9300-48U-A Tested
$799.99
NEW SEALED Cisco C9300L-STACK-KIT
$479.99