Try "knoppix vsync=60" at boot prompt.
Good luck.
I have recently purchased a CD with knoppix 3.3 I have tried it on both my computers. In each case the boot procedure continues normally until the point that I expect to see the desktop. Instead I receive the following message OUT OF RANGE
Hf 28 - 70 Khz
Vf 40 - 120 Hz
79 KHz/ 74 Hz
The second computer gets the same result but with different numerals.
What do I have to do to correct this problem ?
Try "knoppix vsync=60" at boot prompt.
Good luck.
I am sorry but that did not have any effect when I again tried it on either of the computers.
derek wilkinson
If memory serves me properly, that message is actually coming from the monitor, not the software. The software is probably sending a signal that isn't compatible with your specific brand/type of monitor.Originally Posted by derek wilkinson
--Chris ^_^
Have you tried knoppix xvrefresh=60 noddc some details on the hardware you are using may be useful as well, other cheat codes you may wish to add to the line.
Thank you for your help. I have at least got it to work on one computer but am not sure why. If I may combine yopur suggestions - I have a daytek 77A on one computer and a Princeton eois on the other. I noted one other odd thing. After the out of range message appears there is a verbal message which as far as I can make it out says "initiating ?sequence". Unfortunately at 78 my hearing is not too good. I tried some of the other cheats without effect. Then I noticed that on booting it reaches the point where there is a message "starting single x-window but it disappears before I have time to read it . So I hit the pause button and got a blank screen followed after a few seconds by the knoppix desktop. So it works but I don't know why. This works with the vsync = 60 at boot
It is saying "initiating startup sequence" that is a good sign at least the sound is getting detected properly it is definitely having problems with the auto-detection of some hardware in your computers. Firstly have you went into the BIOS in the computers and made sure you have turned off the option for a "Plug'n'Play" OS. Also you should use the knoppix testcd to make sure the disk was burned properly. You may also want to be adding to the cheat codes line the xmodule=?? for the video card you are using. Some more details on the hardware in the machines you are using could prove useful as well.Originally Posted by derek wilkinson
Cisco Nexus 48-Port 10G SFP+ Switch N9K-9396PX w/ 9K-M12PQ 12-Port 40G QSFP
$249.99
Cisco 10-2456-03 Genuine Cisco SFP-10G-LRM V03 10GBASE-LRM SFP+Transceiver
$21.24
Lot of 10pcs Brocade 57-1000012-01 8Gbps SWL 850nm SFP+ Optical Transceivers
$19.00
SFP-10G-SR V03 Original CISCO 10-2415-03 850nm 10GBASE-SR SFP+ Multi mode Module
$5.89
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
10Gtek ASF-10G-T 10GBase-T 10GbE SFP+ to RJ-45 Copper Optical Transceiver Module
$35.99
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00