-
Junior Member
registered user
Qtparted
I have just booted Knoppix from the CD, and I would like to use QTparted to partition the HDD.
I tried it and I keep getting the following error:
There was a problem with mkfs.ext3
It can only parition 2.13GB out of 40GB for some reason.
Could someone tell me how to make paritions in QTparted?
-
Junior Member
registered user
errors with qparted
Hi !
got the same error. After trying to format the first fs (/dev/hdb2) whole harddisk got locked. I rebooted knoppix from CD and formatted the next step by step (/dev/hdb3 and /deb/hdb4).
Workaround:
set partitions by qparted or other partitioning-program (PQMagic) without fotmatting, reboot knoppix CD, start root shell and format the partitions using "sudo mkswap /dev/hdb1" and the filesystems by "sudo mkfs.ext3 /dev/hdb2" etc (replace hdb1 / hdb2 by your harddrive requirements !)
Works for me.
-----
Update:
Hmmm - seems, that knoppix-inst.sh doesn't like ext3, the partitioning with ext2 works well with qtparted. Will try some more and give feedback in a while.
-
Junior Member
registered user
ok, now I got it
When I first used qtparted (see above) and checked all created linux-partitions with cfdisk they were marked as FAT16-type. (???)
So I used cfdisk instead of qtparted and it worked fine.
(see http://www.knoppix.net/forum/viewtopic.php?t=8363)
I installed knoppix on the second harddrive divided into 4 partitions:
start knoppix from cd
start root shell:
cfdisk /dev/hdb
/dev/hdb1 = swap = type 82
/dev/hdb2 = boot1 = type 83
/dev/hdb3 = anotherboot = type 83
/dev/hdb4 = data = type83
marked /dev/hdb2 as bootable
write all to disk
leave cfdisk and reboot from knoppix-cd
start root shel again
formatted all partitions:
mkswap /dev/hdb1
mkfs.ext3 /dev/hdb2
mkfs.ext3 /dev/hdb3
mkfs.ext3 /dev/hdb4
you can check the result by running cfdisk again (but no writing this time !) - must be all linux ext3 partitions
execute knoppix-install.sh (or knoppix-int.sh für ct-3.4-edition)
selected /dev/hdb2 for destination of installation
wrote lilo into mbr.
so now I can use the old win2k (as long as I need it - hopefully not for very much longer) and knoppix from hd
Thanks to all the other forum posts. Helped a lot !
Similar Threads
-
By jjbergdolt in forum General Support
Replies: 7
Last Post: 07-30-2005, 12:56 PM
-
By mark.johnson in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 04-13-2005, 03:30 PM
-
By xaviers2002 in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 06-24-2004, 06:14 PM
-
By Massimo in forum Ideas
Replies: 3
Last Post: 07-23-2003, 06:59 PM
-
Replies: 8
Last Post: 05-08-2003, 05:47 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
LSI 9207-8i 8-Port SAS Non-RAID 6GBPS PCIe Host Bus Adapter
$34.95
Oracle 7085209 LSI MegaRAID SAS 9361-8i 1GB Cache 12Gbps SAS/SATA PCIe RAID Card
$28.20
Cisco UCS LSI MegaRAID 9271CV-8I SAS2308 PCIe SAS Internal RAID Controller
$28.00
LSI 9223-8I 6GBPS PCIe SAS Internal RAID Controller
$22.75
Inspur LSI 9300-8i Raid Card 12Gbps HBA HDD Controller High Profile IT MODE
$15.98
LSI MegaRAID 9361-8i 12Gb PCIe 8-Port SAS/SATA RAID 1Gb w/BBU/CacheVault/License
$39.95
LSI MegaRAID 9361-8i 12Gbps PCIe 3 x8 SATA SAS 3 8 Port RAID + BBU & CacheVault
$39.00
ORICO Multi Bay RAID Hard Drive Enclosure USB 3.0/ Type-C For 2.5/3.5'' HDD SSDs
$82.49
ACASIS 2.5/3.5 inch 2 Bay SATA USB 3.0 Hard Drive Disk HDD SSD Enclosure 4 RAID
$58.99
Dell PERC H330 PCIe 3.0 x8 RAID Storage Controller 04Y5H1 High Profile
$17.99