-
Junior Member
registered user
Qtparted
I have just booted Knoppix from the CD, and I would like to use QTparted to partition the HDD.
I tried it and I keep getting the following error:
There was a problem with mkfs.ext3
It can only parition 2.13GB out of 40GB for some reason.
Could someone tell me how to make paritions in QTparted?
-
Junior Member
registered user
errors with qparted
Hi !
got the same error. After trying to format the first fs (/dev/hdb2) whole harddisk got locked. I rebooted knoppix from CD and formatted the next step by step (/dev/hdb3 and /deb/hdb4).
Workaround:
set partitions by qparted or other partitioning-program (PQMagic) without fotmatting, reboot knoppix CD, start root shell and format the partitions using "sudo mkswap /dev/hdb1" and the filesystems by "sudo mkfs.ext3 /dev/hdb2" etc (replace hdb1 / hdb2 by your harddrive requirements !)
Works for me.
-----
Update:
Hmmm - seems, that knoppix-inst.sh doesn't like ext3, the partitioning with ext2 works well with qtparted. Will try some more and give feedback in a while.
-
Junior Member
registered user
ok, now I got it
When I first used qtparted (see above) and checked all created linux-partitions with cfdisk they were marked as FAT16-type. (???)
So I used cfdisk instead of qtparted and it worked fine.
(see http://www.knoppix.net/forum/viewtopic.php?t=8363)
I installed knoppix on the second harddrive divided into 4 partitions:
start knoppix from cd
start root shell:
cfdisk /dev/hdb
/dev/hdb1 = swap = type 82
/dev/hdb2 = boot1 = type 83
/dev/hdb3 = anotherboot = type 83
/dev/hdb4 = data = type83
marked /dev/hdb2 as bootable
write all to disk
leave cfdisk and reboot from knoppix-cd
start root shel again
formatted all partitions:
mkswap /dev/hdb1
mkfs.ext3 /dev/hdb2
mkfs.ext3 /dev/hdb3
mkfs.ext3 /dev/hdb4
you can check the result by running cfdisk again (but no writing this time !) - must be all linux ext3 partitions
execute knoppix-install.sh (or knoppix-int.sh für ct-3.4-edition)
selected /dev/hdb2 for destination of installation
wrote lilo into mbr.
so now I can use the old win2k (as long as I need it - hopefully not for very much longer) and knoppix from hd
Thanks to all the other forum posts. Helped a lot !
Similar Threads
-
By jjbergdolt in forum General Support
Replies: 7
Last Post: 07-30-2005, 12:56 PM
-
By mark.johnson in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 04-13-2005, 03:30 PM
-
By xaviers2002 in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 06-24-2004, 06:14 PM
-
By Massimo in forum Ideas
Replies: 3
Last Post: 07-23-2003, 06:59 PM
-
Replies: 8
Last Post: 05-08-2003, 05:47 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
ibm server z series
$16000.00
IBM Power S822 12-Bay Server System Power8 Core 3.42Ghz DVD-Rom Drive 64GB No HD
$399.99
IBM Power 720 POWER7 00E6516 3.6GHz CPU 64GB RAM Server
$209.98
IBM 7944AC1 System x3550 M3 Server 1*Intel Xeon X5650 2.67GHz 4GB SEE NOTES
$26.97
IBM Power 740 8205-E6C Express 8-SFF Power7 3.55GHz CPU 64GB RAM *No HDD* Server
$191.99
IBM System x3500 m3 Server
$100.00
Lenovo IBM x3500 M5 Tower Server E5-2670 V3 2.30GHz
$999.99
IBM SYSTEM x3200 M2 Server - HDD wiped, No OS
$75.00
IBM 8203 E4A p520 Server 8203-E4A 4.2GHz 2-Core POWER6 32GB RAM / NO HDD USED
$99.99
1U IBM x3550 M5 4 Bay SFF SAS3 Server 2x E5-2683 V3 28 Core 128GB DDR4 2x Tray
$318.00