-
Junior Member
registered user
Qtparted
I have just booted Knoppix from the CD, and I would like to use QTparted to partition the HDD.
I tried it and I keep getting the following error:
There was a problem with mkfs.ext3
It can only parition 2.13GB out of 40GB for some reason.
Could someone tell me how to make paritions in QTparted?
-
Junior Member
registered user
errors with qparted
Hi !
got the same error. After trying to format the first fs (/dev/hdb2) whole harddisk got locked. I rebooted knoppix from CD and formatted the next step by step (/dev/hdb3 and /deb/hdb4).
Workaround:
set partitions by qparted or other partitioning-program (PQMagic) without fotmatting, reboot knoppix CD, start root shell and format the partitions using "sudo mkswap /dev/hdb1" and the filesystems by "sudo mkfs.ext3 /dev/hdb2" etc (replace hdb1 / hdb2 by your harddrive requirements !)
Works for me.
-----
Update:
Hmmm - seems, that knoppix-inst.sh doesn't like ext3, the partitioning with ext2 works well with qtparted. Will try some more and give feedback in a while.
-
Junior Member
registered user
ok, now I got it
When I first used qtparted (see above) and checked all created linux-partitions with cfdisk they were marked as FAT16-type. (???)
So I used cfdisk instead of qtparted and it worked fine.
(see http://www.knoppix.net/forum/viewtopic.php?t=8363)
I installed knoppix on the second harddrive divided into 4 partitions:
start knoppix from cd
start root shell:
cfdisk /dev/hdb
/dev/hdb1 = swap = type 82
/dev/hdb2 = boot1 = type 83
/dev/hdb3 = anotherboot = type 83
/dev/hdb4 = data = type83
marked /dev/hdb2 as bootable
write all to disk
leave cfdisk and reboot from knoppix-cd
start root shel again
formatted all partitions:
mkswap /dev/hdb1
mkfs.ext3 /dev/hdb2
mkfs.ext3 /dev/hdb3
mkfs.ext3 /dev/hdb4
you can check the result by running cfdisk again (but no writing this time !) - must be all linux ext3 partitions
execute knoppix-install.sh (or knoppix-int.sh für ct-3.4-edition)
selected /dev/hdb2 for destination of installation
wrote lilo into mbr.
so now I can use the old win2k (as long as I need it - hopefully not for very much longer) and knoppix from hd
Thanks to all the other forum posts. Helped a lot !
Similar Threads
-
By jjbergdolt in forum General Support
Replies: 7
Last Post: 07-30-2005, 12:56 PM
-
By mark.johnson in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 04-13-2005, 03:30 PM
-
By xaviers2002 in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 06-24-2004, 06:14 PM
-
By Massimo in forum Ideas
Replies: 3
Last Post: 07-23-2003, 06:59 PM
-
Replies: 8
Last Post: 05-08-2003, 05:47 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
HyperX FURY DDR4 64GB (4x16GB) 3200MHz PC4-25600 Desktop RAM Memory DIMM 288PIN
$129.95
Team T-FORCE VULCAN Z 16GB (2 x 8GB) 288-Pin PC RAM DDR4 3200 (PC4 25600) XMP
$38.99
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
Corsair Vengeance LPX 32GB PC4-25600 (DDR4-3200) Memory NEVER USED LOOSE STICKS
$40.00
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$12.90
Kingston Fury HP32D4U8D8HC-16X 16GB 2Rx8 XMP4-3200-UB1-11 RAM Desktop Memory
$22.00
CORSAIR Vengeance RGB Pro 32GB (2 x 16GB) 288-Pin PC RAM DDR4 3600 (PC4 28800)
$79.95
8GB PC3L-12800S 1600MHz SODIMM DDR3 RAM | Grade A
$12.00
Lot of 50 Samsung/SK Hynix/Kingston (8GB) DDR4 1Rx8 PC4-3200AA Laptop RAM Memory
$599.98
A-Tech 256GB 4x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$287.96