Linux version 2.4.24-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mi Feb 4 01:03:50 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0d4a - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000011ffb800 (usable)
BIOS-e820: 0000000011ffb800 - 0000000011fffc00 (ACPI data)
BIOS-e820: 0000000011fffc00 - 0000000012000000 (ACPI NVS)
BIOS-e820: 00000000ffff0d4a - 0000000100000000 (reserved)
0MB HIGHMEM available.
287MB LOWMEM available.
On node 0 totalpages: 73723
zone(0): 4096 pages.
zone(1): 69627 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 400.918 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 799.53 BogoMIPS
Memory: 288092k/294892k available (1278k kernel code, 6412k reserved, 547k data, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU0: Intel Celeron (Mendocino) stepping 0a
per-CPU timeslice cutoff: 366.06 usecs.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xf603d, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
PCI: Found IRQ 10 for device 00:0a.0
PCI: Sharing IRQ 10 with 00:02.0
PCI: Found IRQ 10 for device 00:0a.1
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xfd000000, mapped to 0xd280d000, size 1984k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:8d70
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda
MA, hdb
io
ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc
io, hdd
io
hda: HITACHI_DK239A-65, ATA DISK drive
hdc: MATSHITA CR-175, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 12685680 sectors (6495 MB) w/512KiB Cache, CHS=789/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
hdc: attached ide-scsi driver.
Partition check:
hda: hda1
ide: late registration of driver.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 12685615 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: CD-ROM CR-175 Rev: 5TCF
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 3276
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 478k freed
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18k (Release Date: Thu Aug 28 10:05:11 EDT 2003)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.01
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 29909 blocks, 65536 bytes/block, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 00:0a.0
PCI: Sharing IRQ 10 with 00:02.0
PCI: Found IRQ 10 for device 00:0a.1
Yenta IRQ list 02b8, PCI irq10
Socket status: 30000010
Yenta IRQ list 02b8, PCI irq10
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x2f8-0x2ff 0x330-0x337 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x3f8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: NE2000 (DL10022 rev 05): io 0x300, irq 3, hw_addr 00:04:5A:A2:9F:60
eth0: found link beat
eth0: autonegotiation complete: 100baseT-FD selected
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:17:44 Feb 4 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Enabling device 00:07.2 (0004 -> 0005)
PCI: Found IRQ 10 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
eth0: found link beat
eth0: autonegotiation complete: 100baseT-FD selected
Serial driver version 5.05c (2001-07-0
with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 232M
agpgart: no supported devices found.
eth0: found link beat
eth0: autonegotiation complete: 100baseT-FD selected