have you found an solution?
you say you see grub, but (I havent used knoppix lately so I can be wrong) knoppix uses LILO nog grub. So what knoppix are you using? and you see grub, what exactly do you see?
Hi,
I am new to the Linux world and KNOPPIX was my first experience with Linux. I was impressed with it and tried to install it on my hdd. All went well until i reboot. I get to the prompt "GRUB" and then nothing happens. Can someone please help me out with this?
Thanks in advance
Cheers,
dantay
have you found an solution?
you say you see grub, but (I havent used knoppix lately so I can be wrong) knoppix uses LILO nog grub. So what knoppix are you using? and you see grub, what exactly do you see?
Hi superstoned,
That was what I thought too. I was baffled to see GRUB prompt greeting me. I THINK that I got over the initial problem I was having. I have had my hdd as the secondary master (there are no primary master or slave, my comp's interior is in a mess and ... I just got too lazy to move my hdd around) and after reading some of the postings, one of them pointed out that I could modify the lilo.conf. So I did and changed boot=/dev/hda to boot=/dev/hdc.
From then on, KNOPPIX loaded ... half way and I get some error message about bad CRC on my hdd and stops. I can't really remember the exact error message right now though. Therefore, I suspect there is something wrong with the hdd but I have been using it for some time and it works.
So, is what I did at the begining (altering the .conf file) the correct thing to do? Or would it have caused some CRC problem (??) to my hdd?
Thanks in advance.
well, its unlikely your disk is broken (or, part of it) but not impossible.
anyway, I'd start moving your hdisk to a propper place (e.g. primary master), it might help. I've seen alot of problems with these things too, esp with raid-hardware present in the system.
and what you did with the conf file is oke, it shouldnt give problems. but you have to re-run lilo for the new config to be applied (guess you did, it worked isnt it?)
Dell PowerEdge R720 Server - 2x8c CPU,256Gb RAM, 128Gb SSD/3x900Gb SAS, Proxmox
$340.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$79.19
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
DELL POWEREDGE T430 SERVER W/ DUAL XEON E5-2609 CPU & 16GB MEMORY
$329.00
Dell PowerEdge R620 4-Bay Server 2x Xeon E5-2690 8 Core 2.9GHz 32GB No HDD H710P
$95.63
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2620V4, 64GB- 512GB RAM, 480GB SSDs
$246.67
Dell PowerEdge R620 Server 2x E5-2650 V2 = 16 Cores H710P 128GB RAM 2x 600GB SAS
$274.99
DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 32GB H730 4xRJ45
$274.00
Dell PowerEdge R440 2X 4214 CPU @ 2.20 GHz 8GB 600GB SAS 2.5-inch Hard Drive
$595.00