Results 1 to 4 of 4

Thread: GRUB ... then nothing

  1. #1
    Junior Member
    Join Date
    Mar 2004
    Posts
    2

    GRUB ... then nothing

    Hi,

    I am new to the Linux world and KNOPPIX was my first experience with Linux. I was impressed with it and tried to install it on my hdd. All went well until i reboot. I get to the prompt "GRUB" and then nothing happens. Can someone please help me out with this?

    Thanks in advance

    Cheers,
    dantay

  2. #2
    Senior Member registered user
    Join Date
    May 2003
    Location
    Utrecht, The Netherlands
    Posts
    298
    have you found an solution?

    you say you see grub, but (I havent used knoppix lately so I can be wrong) knoppix uses LILO nog grub. So what knoppix are you using? and you see grub, what exactly do you see?

  3. #3
    Junior Member
    Join Date
    Mar 2004
    Posts
    2
    Hi superstoned,

    That was what I thought too. I was baffled to see GRUB prompt greeting me. I THINK that I got over the initial problem I was having. I have had my hdd as the secondary master (there are no primary master or slave, my comp's interior is in a mess and ... I just got too lazy to move my hdd around) and after reading some of the postings, one of them pointed out that I could modify the lilo.conf. So I did and changed boot=/dev/hda to boot=/dev/hdc.

    From then on, KNOPPIX loaded ... half way and I get some error message about bad CRC on my hdd and stops. I can't really remember the exact error message right now though. Therefore, I suspect there is something wrong with the hdd but I have been using it for some time and it works.

    So, is what I did at the begining (altering the .conf file) the correct thing to do? Or would it have caused some CRC problem (??) to my hdd?

    Thanks in advance.

  4. #4
    Senior Member registered user
    Join Date
    May 2003
    Location
    Utrecht, The Netherlands
    Posts
    298
    well, its unlikely your disk is broken (or, part of it) but not impossible.

    anyway, I'd start moving your hdisk to a propper place (e.g. primary master), it might help. I've seen alot of problems with these things too, esp with raid-hardware present in the system.

    and what you did with the conf file is oke, it shouldnt give problems. but you have to re-run lilo for the new config to be applied (guess you did, it worked isnt it?)

Similar Threads

  1. Grub
    By tenlientl in forum Hdd Install / Debian / Apt
    Replies: 2
    Last Post: 05-02-2005, 08:23 PM
  2. Trouble with grub...
    By rrfish72 in forum General Support
    Replies: 1
    Last Post: 01-10-2005, 07:32 AM
  3. How to use Grub
    By Neil Young & Crazy Ho in forum General Support
    Replies: 1
    Last Post: 05-14-2004, 07:05 AM
  4. lilo to grub???
    By phantomshado in forum General Support
    Replies: 1
    Last Post: 02-14-2004, 06:45 AM
  5. Getting rid of Grub
    By fingers99 in forum Hdd Install / Debian / Apt
    Replies: 4
    Last Post: 08-10-2003, 04:04 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24 picture

Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24

$117.00



GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE picture

GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE

$74.99



Sonicwall 02-SSC-1874 Compatible 10GBASE-T Copper SFP+ RJ-45 30M Transceiver-876 picture

Sonicwall 02-SSC-1874 Compatible 10GBASE-T Copper SFP+ RJ-45 30M Transceiver-876

$189.05



GENUINE CISCO 25G Base Active Optical SFP cable 3M SFP-25G-AOC3M NEW SHIPS FREE picture

GENUINE CISCO 25G Base Active Optical SFP cable 3M SFP-25G-AOC3M NEW SHIPS FREE

$65.99



Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03  picture

Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03

$8.00



For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Module 10G SFP+ to RJ45 10GBase-T picture

For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Module 10G SFP+ to RJ45 10GBase-T

$48.59



NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping* picture

NEW Sealed Cisco SFP-10G-SR-S 10G SR SFP+ Module 850nmMM *US Shipping*

$15.00



GENUINE Cisco SFP-GE-T EXT 30-1421-01 USA 1000BASE-T RJ45 SFP Transceiver picture

GENUINE Cisco SFP-GE-T EXT 30-1421-01 USA 1000BASE-T RJ45 SFP Transceiver

$9.99



NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping* picture

NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*

$18.00



10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module picture

10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module

$85.00