-
Wireless with Intel Centrino (2100) & Knoppix 3.4
I have just DL'd the 3.4 version. It mentions that the Centrino chip is supported. I have tried getting it to work but to know avail.
The main reason I have loaded Knoppix is to use Airsnort and test the security of the wireless network here.
Can anyone offer any 123 steps to getting this to work?
Thank you in advance.
-
Senior Member
registered user
Hmm. I'd be interested in hearing about this as well. Right now I don't have anything that's using Centrino, but I have thought about getting a new notebook. I've discovered a few wireless issues that I need to email klaus about, but nothing Centrino related as of yet.
-
Originally Posted by
aay
I've discovered a few wireless issues that I need to email klaus about
Any chance you can shre the issue you have already found?
--r00t
-
Can you give the results from iwpriv. I'm not sure if the Centrino drivers support monitor mode - which you will need for airsnort.
-
Originally Posted by
level
Can you give the results from iwpriv. I'm not sure if the Centrino drivers support monitor mode - which you will need for airsnort.
I did get a message saying something about monitor mode but I am unsure what supporting monitoring mode means. I will have a trawl around to see if I can dig up some info. Any pointers from yourself is appreciated too
-
If you ran airsnort you probably got a message " cannot set monitor mode " or something to that effect. If you type the command "iwpriv" (without quotes) and if you don't see monitor listed, then I don't think you can use airsnort with that driver. At least not at the present state of development.
You may want to check their website:
http://ipw2100.sourceforge.net/
-
Originally Posted by
level
If you ran airsnort you probably got a message " cannot set monitor mode " or something to that effect. If you type the command "iwpriv" (without quotes) and if you don't see monitor listed, then I don't think you can use airsnort with that driver. At least not at the present state of development.
You may want to check their website:
http://ipw2100.sourceforge.net/
Where would one type iwpriv? As you can gather I am quite new to Knoppix. I will look at the link you provided meantime. Thanks for the heads up
-
Senior Member
registered user
Originally Posted by
r00t 4orce
Originally Posted by
aay
I've discovered a few wireless issues that I need to email klaus about
Any chance you can shre the issue you have already found?
--r00t
Sure, basically it has to do with wireless usb devices. With the release of 3.4 I tired to get my Linksys wusb12 device working. 3.4 detected it and loaded the prism2_usb driver which is great. The device was designated as wlan0. Unfortunately I don't think it's possible to designate the essid or to use a wep key with usb wlan devices when using Knoppix from the cd. The reason is as follows: the configs for wireless pcmcia cards are stored in /etc/pcmcia/wireless.opts. This is the file that is written to when users plug in their essid and wep keys using wlcardconfig. The problem is that the config file for wlan devices is /etc/wlan/wlan.conf, but on Knoppix this is just a symlink to /KNOPPIX/etc/wlan/wlan.conf which is of course is read only. The real wlan.conf needs to be placed in /etc/wlan/wlan.conf and made writeable just like /etc/pcmcia/wireless.opts is. After that, Klaus could hopefully update wlcardconfig so that it could plug in the right values to wlan.conf. BTW, if i'm mistaken about any of this, please someone let me know. I haven't fooled around much with these wireless usb devices, but from what I understand this info is correct and these setting will need to be adjusted if people are to get their usb wireless devices working.
-
Junior Member
registered user
Centrino...
headshot,
What have you tried to get the chipset working? I booted first into 'knoppix26', and I didn't get it to work in there (I didn't try very hard), but when I just booted from plain 'knoppix', my card was recognized, and I ran the iwconfig in the Knoppix menu under Networking. Worked like a charm.
Please post your reply & problems.
Scott
-
Senior Member
registered user
Re: Centrino...
Originally Posted by
barl0w
headshot,
What have you tried to get the chipset working? I booted first into 'knoppix26', and I didn't get it to work in there (I didn't try very hard), but when I just booted from plain 'knoppix', my card was recognized, and I ran the iwconfig in the Knoppix menu under Networking. Worked like a charm.
Please post your reply & problems.
Scott
You're talking about a usb device? You were able to configure essid and wep with iwconfig?
Similar Threads
-
By squard in forum Networking
Replies: 0
Last Post: 03-20-2005, 10:27 PM
-
By momceras in forum Networking
Replies: 2
Last Post: 02-06-2005, 07:45 PM
-
By momceras in forum Laptops
Replies: 5
Last Post: 02-01-2005, 10:32 PM
-
By muzicman82 in forum Networking
Replies: 1
Last Post: 11-23-2004, 12:51 AM
-
By andreas2000 in forum Networking
Replies: 4
Last Post: 10-27-2004, 09:08 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 64GB H730 4xRJ45
$314.00
Dell Poweredge R730xd 2.5in 2x E5-2690 v3 2.6ghz 24-Cores 64gb H730 2x 750w
$189.99
HP ProLiant DL360 Gen9 Server 2x E5-2699v3 2.3GHz =36 Cores 32GB P440AR 4xRJ45
$309.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$210.00
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2680V4, 64GB- 512GB RAM, New SSDs
$354.67
Dell PowerEdge R710 6-Bay 3.5" 1x E5606 2.13GHz 24 GB DDR3 iDRAC 6 Ent. Server
$160.00