-
Senior Member
registered user
usb external modem not found - help
info center finds the external usb "softmodem" - but i cant locate it with kppp under devices...
yes, first it was with an lt winmodem, now its with external usb modem.
problem is that i am transfering any solutions, of working stuff from a "dumb" webbie tv screen over to my pc - so posting output from anything is going to be troublesome, if not very diffiult.
how can i get knoppix/debian to get to the modem, and get connected, so that i can at least relay data directly to posting, if not a workaround, get the modem happy.
thanks immensely,
Cuddles
-
Senior Member
registered user
Ok, I've got my old system sitting next to the Knoppix/Debian 3.3 (new system) - running.
Info Center reports the modem as such:
SGS Thomson electronics (0x483)
56K Softmodem (0x7554)
I ran around looking in the dmesg output, and it appears that the usb router hub (usb.c) is seeing it - I have tried everything in KPPP under device, from tty to ttyI, to acm, etc... I can't seem to locate where the usb hub has placed the device, and then I assume I need to make a "link" from /dev/modem to this? (like I did with the WinModem on this system)
But, for the life of me, I can't figure out where to start, or find the device I need to link to....
Anyone? Can someone help me get my new "wiz-bang, super-dooper, red hot" system up and gettin on the net?
Thanks for any assistance,
Cuddles
-
You don't name the manufacturer, Thomson SGS could just be chipset manufacturers.
Anyway a googling on the model finds this:
http://www.aztech.com.sg/products/um9800.htm
In that case you're lucky since they provide a linuxdriver with readme, but I can't tell if it's the right one.
Knoppix comes with acm driver that works with some modems.
You would then have to do as root.
$modprobe acm (to load the drivermodule, and hopefully the modems lights turn on)
$lsmod (to see if it's loaded)
$mknod /dev/usb/ttyACM0 c 166 0 (to set up a device node)
$ln -s /dev/usb/ttyACM0 /dev/modem (to link it so that kppp finds it as /dev/modem)
Hope something works out.
In the meantime you should probably avoid anything that says softmodem, they're usually winmodems, though some work with linux too.
I'm not actually quite sure about knoppix and modems since I connect through eth0 to adsl.
-
Senior Member
registered user
Tried above, failed to activate, nor allow minicom or KPPP to find and use modem...
Looking at package for modem, he is what I see as informational:
Jaton
USB Communicator v.92 faxmodem with voicemail and caller id
V.92
features:
modem on hold, quickconnect, increase upload speed to 48kbps, ITU-V.90.V.92 compliant, V.80 video conferance ready, plug and play, and "S... tm Modem Chipset] unfortunately, the "Void is seal is broken" sticker covers the Sxxxxxx stuff. Shesh, and it is permanently stuck to the box.
thanks for the help, hopefully this helps a little....
Cuddles
-
A look at www.jaton.com does suggest that you have a winmodem and they don't seem to have drivers for linux.
You could try taking it back to the shop and ask them to change it to a hardwaremodem, or hope that someone has managed to make a similar piece of equipment work in linux.
External serial port modems are usually fine with linux but usb ones are mostly paperweight if they are softmodems made for windows.
Well, google around and you might find a driver.
-
Senior Member
registered user
Its going back to the store... I spent $40 more than a standard "winmodem" with the promise that this was a "standard" modem. So, tomorrow its going back, and this time an external serial modem is taking its place.
BTW - since installing 3.3, i've started to get crashes, Crash Guard within KDE yells about something causing a crash, and that "something" is sending "signals" to software to have them shutdown - first time is was lib[something]c++ - and all I was doing was viewing the KMenu - nothing running. The next time I was playing Penguin Solitaire, and some service sent a sigsys[something] that signals software/services to abort.
I since blew away 3.3, and went back to 3.2 - but that too is having similar problems. I can be logged in as Root, do anything, or nothing, and the system goes to black screen and causes the user to be logged out, and the LOGIN screen appears - = - I think my new system has some serious problems. Either processor, memory, hard drive, or installed OS issues. Could be on-motherboard issues, or even the motherboard itself....
Oh well, so much for a nice start of the year...
Cuddles
Similar Threads
-
By bako in forum Hardware & Booting
Replies: 10
Last Post: 04-21-2005, 11:29 PM
-
By agency in forum Hardware & Booting
Replies: 4
Last Post: 12-14-2003, 07:07 PM
-
By DavidTempler in forum Networking
Replies: 9
Last Post: 07-04-2003, 07:15 PM
-
By sopo in forum Hardware & Booting
Replies: 0
Last Post: 05-29-2003, 11:40 AM
-
By in forum General Support
Replies: 1
Last Post: 12-26-2002, 07:20 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
H261-Z61 2U 24SFF AMD Server 8x EPYC 7702 512-Cores 2048GB RAM 8x25G NIC 2x2200W
$13292.18
SuperMicro SYS-E100-9APP Fanless Server Firewall 4core 8GB RAM 256GB M.2 Mini PC
$165.00
Genuine HP ProLiant MicroServer Gen8 Intel Pentium G2020T 2.5GHz 712318-001
$199.95
HPE ProLiant MicroServer Gen8 Intel Xeon E3-1265L 16GB ECC PCIe x16 4x1TB HDD
$249.99
SuperMicro Server 505-2 Intel Atom 2.4GHz 8GB RAM SYS-5018A-FTN4 1U Rackmount
$202.49
Supermicro SYS-E50-9AP-N5 Mini Fanless Server pfSense 5x 1GbE Atom E3940 8GB RAM
$162.00
Open Eye OE-MTX08 8TB Micro Server With Linux (Boots To Login) No Accessories
$294.95
Supermicro 5018A-FTN4 Rack Server - Black
$125.00
1U 20" Short Depth Server Firewall PFSense X11SSH-F Xeon 3.5Ghz 32GB RAM NVME
$247.00
1U Supermicro Server 10 Bay 2x Intel Xeon 3.3Ghz 8C 128GB RAM 480GB SSD 2x 10GBE
$297.00