-
Junior Member
registered user
Knoppix won't boot after HD install
All right, I have a new problem. I've installed knoppix to my HD, but I can't get it to boot. It shows the NT bootloader and XP boots, but I can't see any sign of knoppix. I used the knoppix 3.7 installer and selected for lilo to be installed in MBR. Any advice would be greatly appreciated.
-
Junior Member
registered user
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
-
Senior Member
registered user
Originally Posted by
ixalarx
Right. I looked in cfdisk and noticed that my windows partition was marked as bootable, my linux partition wasn't. Sould I just mark my linux partition as bootable? That may seem like a stupid question, but I don't know what I'm doing and don't want to screw anything up. Again, thanks for any help you can provide.
No, you don't want your linux partition set to bootable, lilo will boot it. It sounds like lilo did not install properly if the first screen you see is XP booting. Boot into your HD install from the CD with 'knoppix lang=us root=/dev/hda5 noinitrd ro' (replace hda5 with the correct partition for your install). Then check /etc/lilo.conf to see if it is correct. It should have 'boot=/dev/hda', an entry for knoppix and an entry for windows. Then open a console & 'sudo lilo' to try to install lilo from the HD install. Follow up on any error messages.
One of the bugs in the hdinstaller is that if something goes wrong with the lilo install it doesn't report back to the user, it just continues on without installing lilo. One potential source of trouble is that the installer adds any cheatcodes in effect to the 'append=' line in lilo.conf & lilo sometimes doesn't like things repeated...like for instance if you are using the cheatcode 'vga=normal' this will conflict with the 'vga=791' which is part of the default lilo.conf.
-
Junior Member
registered user
Okay, I checked the file and it looks fine, but when I ran lilo at the command line I got this output:
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
/dev/mapper/control: open failed: No such device
Is device-mapper driver missing from kernel?
Incompatible libdevmapper 1.00.19-ioctl (2004-07-03)(compat) and kernel driver
Warning: Unable to determine video adapter in use in the present system.
Added Linux *
Added Linux(2.4)-1
Added Linux(2.6)-2
Warning: CHANGE AUTOMATIC assumed after "other=/dev/hda2"
Device 0x0300: Inconsistent partition table, 2nd entry
CHS address in PT: 619:0:1 --> LBA (9944235)
LBA address in PT: 9359280 --> CHS (582:150:1)
Fatal: Either FIX-TABLE or IGNORE-TABLE must be specified
If not sure, first try IGNORE-TABLE (-P ignore)
I have no clue what this means, but I hope it helps.
-
If not sure, first try IGNORE-TABLE (-P ignore)
lilo -P ignor
and reboot
-
Junior Member
registered user
I would have tried the lilo -P thing, but now when trying to boot from HD with the CD it doesn't start at all. It gets to
"Running from HD, regenerate ld.so.cache and modules.dep..." then stops. The light on the case shows no HD activity. Am i pretty much screwed here?
-
what do u get on boot is lilo now or still xp
sorry have to leave
-
Junior Member
registered user
No, I'm using the CD to boot from the HD.
-
using the CD to boot from the HD.
how
fromhd
or
whith chroot
and if you boot from your hd what's happend
see your tomorrow
-
Junior Member
registered user
Sorry, I was pretty rushed and couldn't post very coherently. I'll just recap what happened. After reading your post about using lilo -P, I tried to boot using Crashed's instructions "knoppix lang=us root=/dev/hda5 noinitrd ro", but the booting seemed to stop after showing "Running from HD, regenerate ld.so.cache and modules.dep..." It still does not show anything while booting without the CD but the NT bootloader.
Similar Threads
-
By AlphaBluesMan in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 02-24-2006, 10:44 AM
-
By AgustinCordoba in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 09-20-2005, 04:43 PM
-
By bigrobot in forum Networking
Replies: 0
Last Post: 12-06-2004, 02:32 PM
-
By ku in forum General Support
Replies: 1
Last Post: 03-17-2004, 11:41 PM
-
By orvil in forum Hdd Install / Debian / Apt
Replies: 5
Last Post: 05-29-2003, 02:09 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
HP ProLiant ML350 Gen 9 Server 64GB RAM 2.4GHz Xeon 12-Core E5-2667 v3
$300.00
Dell Poweredge R620 2x E5-2680 2.7ghz 16-Cores / 128gb / H710 / 2x Trays / 750w
$199.99
Dell R730xd 26 Port SFF 2x E5-2697v4 36-Cores H730 128GB Server 2x SFP 10G ENT
$490.00
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$345.00
HP ProLiant DL380 Gen9 Server 1x Xeon E5-2620V3 2.40 GHz 32 GB RAM No OS No HDD
$129.95
Chenbro NR12000 1U 1x 8m QUAD CORE E3-1230v2 3.3GHz 8GB RAM NO HDD
$239.00
SuperMicro Server 505-2 Intel Atom 2.4GHz 8GB RAM SYS-5018A-FTN4 1U Rackmount
$202.49
DELL PowerEdge R630 8SFF Server 2x E5-2699v3 2.3GHz =36 Cores 64GB H730 4xRJ45
$345.00
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2620V4, 64GB- 512GB RAM, 480GB SSDs
$300.00