-
Knoppix shows eth0 and eth1, but I have 1 NIC
I am running Knoppix 4.0 HD Install from DVD.
During bootup, netcardconfig or ifconfig, I see 2 NICs (eth0 and eth1) but I only have 1 physical NIC (I do not have built in wireless.)
eth0 fails to get an address via DHCP or work with a static IP, and eth1 gets an address via DHCP.
I'd like to configure Knoppix to use the interface name eth0 rather than eth1 and ignore the phantom card.
Thanks
-
Administrator
Site Admin-
Re: Knoppix shows eth0 and eth1, but I have 1 NIC
Originally Posted by
chrisup
I am running Knoppix 4.0 HD Install from DVD.
Does Knoppix work correctly when booted from the DVD, not from the install? From years of watching these forums I would say that the networking failing after a hard disk install is the most common Knoppix install problem (and things like this are a major reason why many of us advise against hard disk installs of Knoppix).
-
Thanks for the reply.
The live DVD behavior is the same as the HD install.
I like the Knoppix HD install because it is less time consuming than most distros, and has all the packages I need ready to go. (I'm sort of lazy)
-
Knoppix shows eth0 and eth1, but I have 1 NIC
I think I see what your saying, so, this might be part of the answer.
Even though there's not a card physicly present at the lan port location you mention. Knoppix's start-up routine, by default, will turn the software for both lan ports (eht0 & eth1) ON, and, attempts to broadcast a DHCP ID signal for other available computers on a network.
It may take a few more seconds to boot, but, I've not seen an adversy effects to the system, other then a slight delay till the ports times out.
Apparently this is on the DVD, and, carries over to a hard drive installation.
You should be able to disable this somewhere in the startup routine, if it's disturbing you. which I'm syre someone else knows better about.
-
Senior Member
registered user
if there is a firewire port on that computer it might be seen as a ethernet card.
-
I do have a built-in firewire port. Unless you have an easy suggestion to disable the firewire networking I think I'll accept the eth1-eth0 scenario. Thanks for the replies so far everyone.
Similar Threads
-
By R. Henze in forum German Forum
Replies: 0
Last Post: 07-17-2007, 07:17 AM
-
By R. Henze in forum Hardware & Booting
Replies: 0
Last Post: 07-14-2007, 08:34 AM
-
By Micodat in forum Hardware & Booting
Replies: 0
Last Post: 06-27-2006, 07:11 AM
-
By paradigm_shift in forum Networking
Replies: 0
Last Post: 07-15-2005, 05:41 AM
-
By HAiRYANiMAL in forum General Support
Replies: 9
Last Post: 05-19-2003, 01:07 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Vintage 5362 IBM System/36 Mini-Computer Mainframe 5291 2, CRT Terminal DM12N501
$219.99
Vintage Hewlett Packard HP 2100S Microprogrammable Computer System Mainframe #2
$1499.99
Sierra Automated Systems- 32000, Stereo Audio Routing Switch. MAIN FRAME (USED)
$1200.00
Vintage Hewlett Packard HP 2100A Microprogrammable Computer System Mainframe
$1499.99
6 Vintage Computer Tape Reels mainframe 3200 5000 data ibm magnetic processor
$99.00
vintage lot of 3 computer tapes mainframe data ibm magnetic reels
$25.00
1pc Vintage Soviet Aluminum Hard Drive 14in Platter Mainframe IZOT ES-5053 USSR
$14.99
Very Rare Vendex Headstart II Computer + Keyboard Mouse CRT Monitor Powers On
$209.99
Sage MAS 90 Software for Windows Financial Reporting Mainframe Collection
$339.99
Xargon 1 Beyond Reality RARE Game Floppy 3.5” Floppy Mainframe Collection
$349.99