-
Problem when configuring network on Knoppix 5.1.0 !
Hello. I have a problem installing my network/internet connection on Knoppix 5.1.0. I use the GUI interface found under Knoppix/Net/ Network Card Configuration. With same properties the inetrenet connection works fine with Knoppix 3.9 and Knoppix-STD ( i don't remember the version ). I think that there's a problem with resolving the names.
How can i configure manually the network ?
> eth0 x.x.x.x netmask x.x.x.x broadcast x.x.x.x up
> route add default gw x.x.x.x
And then what ?
Thank you in advance !
Mitko Kostov, Bulgaria.
-
Senior Member
registered user
Try this : if you can boot-up another system that works with your netcard, use it to obtain your router or modem address as applicable, and (optionally, to avoid unnecessary proliferation of addresses), the address that it allocates to your network card under DHCP.
They are likely to be of the forms (substitute your own figures):
192.168.A.B for the modem/router
192.168.A.C for the netcard
Then in Knoppix netcardconfig answer NO to DHCP,
enter 192.168.A.C for the netcard address
enter 255.255.255.0 Subnet Mask
enter 192.168.A.255 Broadcast
enter 192.168.A.B for Nameserver and Gateway
(Reference: http://www.knoppix.net/forum/viewtop...287&highlight= )
Also you might have to command: ifconfig eth0 mtu 1500
(Reference: http://www.knoppix.net/forum/viewtopic.php?t=26867 )
Good luck
-
The thing is that my net provider doesn't use DHCP and i have configured proparly and worked with the addresses for eth0, netmask, gateway and broadcast on Knoppix 3.9 and STD, but on 5.1.0 there's a problem.
-
Administrator
Site Admin-
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
This post cannnot help me, beacause there is nothing helpful for me. I want to know how to start the nameserver, after editing /etc/resolv.conf.
-
Senior Member
registered user
Originally Posted by
Fly
The thing is that my net provider doesn't use DHCP and i have configured proparly and worked with the addresses for eth0, netmask, gateway and broadcast on Knoppix 3.9 and STD, but on 5.1.0 there's a problem.
[1] OK then from this you know your "nameserver/gateway" address (and the other network addresses !!! ) to enter into netcardconfig when you answer "NO" to "Obtain address automaticaly (DHCP)?"
!!! But DO NOT use Broadcast 255.255.255.255 with Knoppix 5.1 (please see earlier posting Friday Mar 16, 2007 5;17pm)
Originally Posted by
Fly
This post cannnot help me, beacause there is nothing helpful for me. I want to know how to start the nameserver, after editing /etc/resolv.conf.
[2] Have you confirmed that /etc/resolv.conf was correctly edited by netcardconfig as used in [1] above ?
[3] What is the value of MTU shown by the command: iconfig eth0 ?
(if you still have a problem it would help to post the full output of iconfig eth0 )
-
Hello again. The problem was very simple : i configured eth0 and my LAN card was identifyied as eth1.
I'm really sorry.
Similar Threads
-
By kckirk3 in forum Networking
Replies: 0
Last Post: 06-16-2009, 06:41 PM
-
By uncleelvis in forum Networking
Replies: 10
Last Post: 09-21-2008, 06:53 AM
-
By pboodi in forum Networking
Replies: 0
Last Post: 07-22-2006, 11:32 PM
-
By berto in forum Networking
Replies: 1
Last Post: 03-01-2004, 02:03 AM
-
By johnsandidge in forum Networking
Replies: 2
Last Post: 01-06-2004, 04:02 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Dell R730 w/ 2x E5-2650v3 10c, 192GB (12x16GB) RAM, H730 Mini, 2x 750W PSU
$499.99
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$210.00
Dell PowerEdge R720xd Dual Intel Xeon E5-2660 v2 @2.20GHz 128GB RAM No HDD H710P
$249.99
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
DELL PowerEdge R730 Server 2x E5-2680v4 2.4GHz =28 Cores 32GB H730 4xRJ45
$284.00
Dell PowerEdge R620 Server - 128GB RAM, 2x8c CPU, 128Gb SSD/3x900Gb SAS, Proxmox
$260.00
Dell Poweredge T430 8 Bay Server Dual Xeon E5-2683 V4 32 Cores 64GB DDR4 2X SSD
$799.00
DELL PowerEdge R730XD Server 2x E5-2680v4 2.4GHz =28 Cores 32GB H730 4xRJ45
$304.00
DELL PowerEdge R730 Server 2x E5-2690v3 2.6GHz =24 Cores 64GB H730 4xRJ45
$314.00